- Home
- 2K Ceramic CB Satin and Activator
Details
2K Satin Ceramic Chassis Black — our most durable, chemical-resistant, and easiest-to-spray Chassis Black yet!
Eastwood's 2K Ceramic Chassis Black is a super-durable satin coating that's not only beautiful, but also tough as nails. Our proprietary formula imbeds finely ground nano-ceramic particles into a high-quality 2K (2-component) 4:1 chemical base to create the ultimate, factory-correct finish. 1-quart satin Ceramic Chassis Black comes with 8-oz. activator; you'll need 2 quarts of Chassis Black for a full-frame vehicle.
- Highly chip-resistant
- Incredibly UV-resistant
- Chemical-resistant
- Dries fast
There are no upsell products available.
See this product in action!
About 2K Ceramic CB Satin and Activator
This is our most durable, chemical-resistant, and easiest-to-spray Chassis Black yet! And since it's formulated with ceramic, it offers even better abrasion resistance! Easy 4:1 mix with the 8-oz. 21854Z Activator included. Spray with a 1.3mm-nozzle or larger spray gun. Covers about 50 sq. ft. in 2 coats for complete hiding. Withstands up to 300-degreeF peaks. For the strongest durability, apply over our 50242ZP Epoxy Primer (sold separately). For professional use only. Contains isocynates. Proper respiratory protection must be used.
Product information sheet - Click Here
Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations; check with your local and state guidelines as some areas may have stricter regulations than others.
Eastwood 2K Ceramic Chassis Black is easily applied with your HVLP spray gun using a 1.3mm or larger nozzle. Provides complete hiding in 2 coats; allow 10 minutes between coats. Refer to product label for more complete application directions and safety information. Can be applied directly over our 50242ZP Epoxy Primer (sold separately) after 60 minutes to 5 days without scuffing.
(Q) Can Eastwood Ceramic Chassis Black be applied directly over other finishes?
(A) Generally, Eastwood Ceramic Chassis Black can be applied over most thoroughly cured finishes (meaning, cannot be indented with a thumbnail). Scuff first with 320- to 600-grit sandpaper and test a small area before coating the entire area. If lifting occurs, remove the lifting paint, sand the surrounding area, and seal the surface by priming first with our 50242ZP Epoxy Primer mixed with 50243ZP Epoxy Primer Catalyst. NOTE: Eastwood Epoxy Primer can be reduced up to 20% with 50104ZP Zero-VOC Urethane Paint Reducer to use strictly as a sealer.
(A) Generally, Eastwood Ceramic Chassis Black can be applied over most thoroughly cured finishes (meaning, cannot be indented with a thumbnail). Scuff first with 320- to 600-grit sandpaper and test a small area before coating the entire area. If lifting occurs, remove the lifting paint, sand the surrounding area, and seal the surface by priming first with our 50242ZP Epoxy Primer mixed with 50243ZP Epoxy Primer Catalyst. NOTE: Eastwood Epoxy Primer can be reduced up to 20% with 50104ZP Zero-VOC Urethane Paint Reducer to use strictly as a sealer.
This product is designed for use by trained professionals. Read and understand all warnings and directions before use. Do not use without sufficient ventilation. Users must wear an appropriate, properly fitted, NIOSH-approved, activated-charcoal cartridge respirator if a forced fresh-air system is not available. Do not use this product, or be exposed to its spray mist or vapors, if you have respiratory problems, or are pregnant or nursing. Keep out of reach of children and pets. This system comprises multiple components; once mixed, this system will include the hazards of all components.
Companion Products
Buy online or call 1-800-343-9353
 |
 |
 |
 |
 |
 |
 |
|