• Home
  • 8pc Dual-Cut Carbide Burr Set - 1/4in Shank
8pc Dual-Cut Carbide Burr Set - 1/4in Shank is rated 4.7 out of 5 by 14.
Rated 5 out of 5 by from Surprised I have used Eastwood Carbide bits in the past and they exceeded my expectations. I used them for porting a Cummins head, aftermarket exhaust manifold, and turbine housing. These bits remain chip free and sharp through many hours of use.
Date published: 2015-07-21
Rated 5 out of 5 by from Quite Happy I wasn't expecting the quality and durability for the price, so was pleasantly surprised. Even the holding-case is nice, form-fitting with magnetic-latch. I punished a couple of these on inside-corner weld-beads, and metal-chips were just flying! No bluing (yet) either.
Date published: 2013-11-08
Rated 5 out of 5 by from Good Product I purchased along with the 4 piece dual cut carbide set to port a cast iron MGA cylinder head. I used a variable speed drill rather than a die grinder. Bits are very sharp out of the box, and cut rapidly, especially the rough casting material. My criticism of these bits is that the shaft is too short. The 4 piece set had greater utility due to the longer reach. These are far superior to anything I've ever seen at the local hardware or big box stores.
Date published: 2013-12-09
Rated 5 out of 5 by from Holy Cow If you never used a double cut. Just be fore warned these suckers bit hard and quick and remove materail faster than normal carbide. I was shocked!! Glad I bought them,used for rod beaming and deburring block and heads (Only for heavy materail removel)
Date published: 2011-04-17
Rated 5 out of 5 by from Great performance These were part of my first order from Eastwood, I was very impressed with their performance. I had to ream out some hardened frame steel, light pressure starting out because these burr cutters will cut faster than you realize. When I was done, I could not tell that I had used the cutter, all the teeth were totally intact and not dulled in the least. I plan to equip my shop with Eastwood tools, GREAT TOOLS EASTWOOD !!!!
Date published: 2012-03-13
Rated 5 out of 5 by from must have tool good quality, just the right tool for cleaning up radius areas
Date published: 2014-08-06
Rated 2 out of 5 by from Good luck Bought these a couple weeks ago and went to use them to clean up some rough iron casting and as soon as I put it on the material it broke in half. The others seem to be fine. Also I was overcharged for the product
Date published: 2015-07-03
Rated 5 out of 5 by from Very good product I received these double angled cutters. WOW, they do remove material, all you have to do is guide them, and let the chips fly. I will re-order when my set gets dull.
Date published: 2013-12-11
  • y_2017, m_3, d_25, h_5
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_14
  • loc_en_US, sid_11779, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

Are these Tungsten Carbide or just Carbide?

Asked by: Frank Furter
These are strictly Carbide.
Answered by: KHoffnagle
Date published: 2017-03-09

What is over all length of the burs? Can they be used on cast iron?

Asked by: RustyHank
All burrs have a 1-1/2" long, 1/4" shaft. Then since the burrs have slightly different sizes the over all length will change a bit.
Answered by: S Church
Date published: 2016-10-26

Are these good for aluminum?

Asked by: Shaub
You can certainly use these on aluminum.
Answered by: S Church
Date published: 2016-06-13

are they usa made

Asked by: ohio
No made in China
Answered by: SeanA
Date published: 2015-01-29
  • y_2017, m_3, d_25, h_1CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_US, sid_11779, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

8pc Dual-Cut Carbide Burr Set - 1/4in Shank

Item #11779 Brand: Eastwood

Precise metal removal when shaping,
leveling, or porting ferrous metals


Shape and deburr quickly and accurately with Carbide Burrs These 8 carbide burrs are the preferred choice for precise metal removal when shaping, leveling, or porting cast iron, steel and other ferrous metals.
  • 2 cylindrical burrs
  • 2 cylindrical/radius-end burrs
  • 2 ball-shaped burrs
  • 2 cone/radius-end burrs

More info...

About 8pc Dual-Cut Carbide Burr Set - 1/4in Shank

Double-cut and precision-ground for vibration-free operation in your 20,000-rpm die grinder. All burrs have a 1-1/2" long, 1/4" shaft. 90-day mfr's. warranty.


2 cylindrical burrs: 1/2" x 1" and 3/8" x 3/4"
2 cylindrical/radius-end burrs: 3/8" x 3/4" and 1/4" x 5/8"
2 ball burrs: 1/4" and 3/8" diameters
2 cone/radius-end burrs: 3/8" x 3/4" and 1/2" x 1"

Customer Reviews

Questions & Answers

Customers also viewed: