Tag Archives: 302

  • Mustang Project Resolution Phase 7- It's looking like a car again!

    On the day of the 2013 Summer Classic our team was still cleaning and detailing the car up until the beginning of the show! We rolled it out mostly complete and the reaction from the spectators was great. The Eastwood Blue Pearl paint REALLY pops in the sun!  Click Here To Read Full Post...
  • Project Resolution Phase 3 Teardown

    Since our last post we've been busy working on disassembling the car down to just a rolling shell. This meant we had to removed the entire drivetrain and start deciding if we were going to keep the original or get a replacement engine. The engine and transmission came out pretty easy when using the Folding Engine Hoist. We then separated the engine and transmission and put the engine on a Ford Small Block Rolling Engine Stand so we could easily move it around the shop.

    Meanwhile, some of the other members of the team worked on sanding the fenders and doors down to bare metal using the Eastwood Stripping Discs and then sprayed them with Eastwood Fast Etch to keep them from flash rusting while they wait their turn for bodywork and shiny paint.

    After looking over the engine we decided that this engine had been neglected for quite sometime and even the original waterpump was still on the engine! When Tim went to remove the bolts out of the waterpump just about every single one broke off. This is going to cause a lot more work as we now have to extract each broken bolt. This task will include removing the harmonic balancer on the crank and the timing chain cover to get to the bolts that broke. Let's hope this doesn't require some serious surgery!

    Once we were tired of fighting with broken bolts we moved on to removing the front radiator support on the car. This is NOT an easy job even on the best day. First of all you have to drill out numerous spot welds and the number of spot welds on each side of the radiator support are not equal. It seems like the spot welder in the factory just did however many felt right that day.. or two guys were spot welding on each side and one did way more than the other. The other problem we had was that the car has been hit in the front and some of the metal was bent and damaged. We took turns drilling spot welds with the Eastwood Spot Weld Cutters and slowly we were able to peel the old radiator support off of the front of the car. We'll have to do some hammer and dolly work to the remaining parts on the front end, but so far the CJ Pony replacement radiator panel seems like it will fit pretty well.

    Next up we will have to remove the damaged inner fender skirt panel and mock it all up to make sure the front sheet metal will sit correctly when we're done. Soon we'll be firing up the MIG 175 and the TIG 200 to weld these panels in place. Stay tuned, we're just getting warmed up!

    Related Eastwood Products:

      Click Here To Read Full Post...
  • Project Resolution Becomes a Shell

    We've been VERY busy since our last update. We've decided that the best way to fix the body damage in the inner fender was to remove the 5.0 engine from the Mustang. As we dug in we found all sorts of holes drilled in that side of the engine bay from someone using a slide hammer to pull the dents and never filling the holes. This will be a great time to freshen up and paint the bay while we're "in there".

    Since we made the decision to pull the drivetrain out everyone has been arguing over what we should do when we put an engine back into the car. Some ideas we've heard range from mild to wild! We've heard supercharging, turbo, refresh and bring back to stock, a new crate engine, even a wild naturally aspirated engine build (big cam, port and polish, lightened and balanced internals, etc). We're still undecided, but I admit it would be good fun to see what sort of power we could get out of a cheap custom turbo setup on the stock 302 with Eastwood tools (give that TIG 200 a workout!). So we decided to do a compression test on all eight cylinders in case we keep the engine or use it as a base. Surprisingly all cylinders were pretty close and within spec. With the high being 145PSI and the low being 130PSI, this engine has faired better than many other fox body Mustangs out there!

    Now with those numbers recorded, Nick and I tore into the bay removing everything that needed to come off to remove the drivetrain. We're a little behind schedule, so we pulled out the Eastwood Air Tools to get the job done a little faster. We didn't run into that many rusty or seized bolts, but we were surprised that few we did run into, the Composite Twin Hammer Impact Wrench broke them loose with ease. With the use of the impact wrench and the Eastwood Composite Air Ratchet we have the engine hanging by only a few bolts. We're hoping later this week to try and pluck the lump out of the bay and drop it on the engine stand.

    While Nick and I worked on the engine bay Lisa, Amanda, Kevin, and Randy worked on getting the interior taken apart. This area was as dirty and abused as we expected, but Lisa did find a few surprises when she was removing the drivers seat. It turns out that someone had ripped or destroyed some of the seat mounting locations in the floor and made some pretty unsafe repairs. Under the right rear drivers seat bracket they had stripped out the mounting hole and drove a larger sized bolt into the floor pan at about a 45 degree angle. This was a pain to get out! Then she found that in the front someone had ripped out the front left mounting point of the drivers seat. To repair the area they used some painters tape (yes you read that correctly!) and a piece of aluminum plate they shoved into the hole to drive another incorrect bolt into. We're still unsure how they got the plate into the hole. but we imagine a BFH was in the mix!

    The crew got the interior pretty well stripped, the bumpers, rear quarter windows and sunroof removed so far and the car really is in shambles. Some may think the Mustang is ready for the junkyard but we see a fresh slate to start over and give this car a new lease on life. Next we hope to get the engine out and start to tackle the body damage. Repair panels are just starting to roll in from CJ Pony Parts and we can't wait to get these quality repair panels installed!

    If you have an idea what we should do for our new engine, please drop us a comment and let us know you're thoughts! Thanks for following, now get out there and build something yourself! -Matt/EW

    Related Eastwood Products:

    • Safety Goggles

      Protect your eyes from hazards from the front or sides; elastic strap

      Click Here To Read Full Post...
  • Street Rodder Road Tour 1940 Ford Nearing Completion- reassembling a 1940 Ford

    The last time we checked in with Street Rodder and Hollywood Hot Rods the paint on the body was still wet. Since then they've been busy getting the car ready for the first leg of the Street Rodder Road Tour and it's unveiling this weekend. We got these sneak peeks from the crew over at Street Rodder Magazine just the other day.

    After rolling the car back to Hollywood Hot Rods from the paint shop, Troy and crew were ready to start buckling down and assemble the Ford. This is the fun part most times, but it is a tedious process installing all of those freshly painted, chromed, and powder coated parts!

    With the exterior starting to look pretty complete, they moved on to the interior. The team decided to go for a classy, but custom retrim in the 40 Ford. They had some help from a local interior shop to help them meet the deadlines, but it is coming together great. We are loving the color-matched piping details, it really pulls it all together!

    With the Ford looking more like a complete car Troy and his crew moved on to mounting up the drivetrain and making the new Ford Racing Coyote V-8 crate engine live. They opted to go with electronic fuel injection to get the most power out of the engine AND the best fuel mileage possible (for a flowed 5L 302 Mustang Boss Engine that is!). Instead of screwdrivers, carb synchs, and their ears, these guys are using a computer to tune the engine so this car will run as well as the latest pony car from the Ford stable.

    With things really coming down to the line for the Road Tour and the debut this weekend the team at Hollywood Hotrods is really buckling down. Stay tuned for the finished pictures of this beautiful 40 Ford and make sure you come out to the kickoff of the east coast leg of the tour on July 14th at the Eastwood Summer Classic! Thanks for watching and we'll see you in July!

    -Matt/EW

      Click Here To Read Full Post...
  • Eastwood Has a new Project - 1989 Mustang LX 5.0 Project Car

    We regularly brag about the fact that we test, design, and dream up new products in-house here at Eastwood. Testing products requires a good rotation of test vehicles and we've had a number of wrecks we've used in the past. Recently the "powers-that-be" agreed that we should buy a new test vehicle that we could restore as we tested and designed new products. The ideas started flying immediately, "We could` test out a new welding attachment while we replace a rusty lower fender" or "Test a new cleaning product on weathered old vinyl", etc. So the hunt was on!

    1989 Mustang LX 5.0

    After weeks of hunting Craiglist religiously, one of our product developers Joe R. came upon a great deal on a local fox body Mustang for sale. The owner brought it by and we climbed all around it looking for the signs of a good Eastwood project vehicle. Our criteria was like the list of things most would shy away from. We wanted rust, dents, body damage, weathered interior, faded bumpers and paint, etc. Needless to say the seller was a bit confused as we commented on the imperfections the car had "Oh cool, the seats are quite worn!" or "Oh nice, it has been in a fender bender at some point", "Oh look it has some rust in the rockers!". Luckily it wasn't April Fools yet and the seller finally understood why we were acting that way. We struck a deal and the car became ours!

    Mustang LX 5.0

    1989 Mustang LX 5.0

    1989 Mustang LX 5.0

    Fast forward a week and we are now starting to brainstorm where will start on the new addition. We plan to stay pretty conservative in this build, keeping it fairly original (or so we are telling the bosses right now!). But we are always looking for your opinions on what we should do to bring this car back from its beater status! Keep watching the Eastwood Blog as we update on the progression of this Mustang.

      Click Here To Read Full Post...