Tag Archives: fox body

  • Mustang Project Resolution Phase 7- It's looking like a car again!

    On the day of the 2013 Summer Classic our team was still cleaning and detailing the car up until the beginning of the show! We rolled it out mostly complete and the reaction from the spectators was great. The Eastwood Blue Pearl paint REALLY pops in the sun!  Click Here To Read Full Post...
  • Project Resolution- Phase Six

    We decided to replace the entire front clip after too many nasty accident damage surprises. The crew stripped the donor clip down using our stripping discs and our 100lb Pressure Blaster. Once the new nose for Resolution was cleaned, I took the reciprocating saw and began surgery.  Click Here To Read Full Post...
  • Project Resolution- Paint Stripping and Final Teardown

    We've been working on Project Resolution now for a few months and we're finally at a point where we are ready to start going uphill making the car nice again. With the front end removed I was able to remove the inner fender "skirt" and assess the damage that was caused during the accident. So far it looks like the damage was just sheet metal related and the chassis itself is still intact and not tweaked from the accident. We now need to clamp all of the new body panels in place with clecos and test fit the hood and fenders to make sure that our gaps all line up correctly before we begin welding those pieces back in place. I know we will need to do a little bit of hammer and dolly work on the remaining sheet metal around the replacement panels, but it should all be straight forward.

    While I was working on the front end removal the rest of our team has been working diligently removing all of the old red paint and uncovering the filler and previous owner repairs (yikes!). The roof is definitely much worse than we thought. It looks like someone used a "stone" style grinding disc or a cut off wheel to remove the old paint and there is a lot of deep gouges in the metal and some more hidden dents. We will have to take some serious time shaping the roof back to an acceptable point before we can make it shiny again.

    Speaking of damage we've uncovered, the rear hatch had some minor paint pitting around the lower edges, but we wanted to investigate them further. We found some terminal rust in the hatch and that we needed to cut out of the lower edge. Nick has removed the worst rust and is currently making up patch panels to weld back in place with the MIG 135. We hope to have that minor body rust tackled quickly and continue getting the body ready for a skim coat of filler, primer, and finally a new coat of paint! We're still on the fence what color we want to paint the car, so if you have any suggestions feel free to drop us a comment with your opinion!

    We plan to get all of the new body panels welded in place, the major body damage repaired, and all the rust repair done by the next update. July 13th for the Eastwood Summer Classic is getting closer everyday and we need to kick this project into high gear! Stay tuned!

    -Matt/EW

    Related Eastwood Products:

    • Pinch Weld Clamps

      Hold pieces tightly together for pinch welds, flange welds, and more

      Click Here To Read Full Post...
  • Project Resolution Becomes a Shell

    We've been VERY busy since our last update. We've decided that the best way to fix the body damage in the inner fender was to remove the 5.0 engine from the Mustang. As we dug in we found all sorts of holes drilled in that side of the engine bay from someone using a slide hammer to pull the dents and never filling the holes. This will be a great time to freshen up and paint the bay while we're "in there".

    Since we made the decision to pull the drivetrain out everyone has been arguing over what we should do when we put an engine back into the car. Some ideas we've heard range from mild to wild! We've heard supercharging, turbo, refresh and bring back to stock, a new crate engine, even a wild naturally aspirated engine build (big cam, port and polish, lightened and balanced internals, etc). We're still undecided, but I admit it would be good fun to see what sort of power we could get out of a cheap custom turbo setup on the stock 302 with Eastwood tools (give that TIG 200 a workout!). So we decided to do a compression test on all eight cylinders in case we keep the engine or use it as a base. Surprisingly all cylinders were pretty close and within spec. With the high being 145PSI and the low being 130PSI, this engine has faired better than many other fox body Mustangs out there!

    Now with those numbers recorded, Nick and I tore into the bay removing everything that needed to come off to remove the drivetrain. We're a little behind schedule, so we pulled out the Eastwood Air Tools to get the job done a little faster. We didn't run into that many rusty or seized bolts, but we were surprised that few we did run into, the Composite Twin Hammer Impact Wrench broke them loose with ease. With the use of the impact wrench and the Eastwood Composite Air Ratchet we have the engine hanging by only a few bolts. We're hoping later this week to try and pluck the lump out of the bay and drop it on the engine stand.

    While Nick and I worked on the engine bay Lisa, Amanda, Kevin, and Randy worked on getting the interior taken apart. This area was as dirty and abused as we expected, but Lisa did find a few surprises when she was removing the drivers seat. It turns out that someone had ripped or destroyed some of the seat mounting locations in the floor and made some pretty unsafe repairs. Under the right rear drivers seat bracket they had stripped out the mounting hole and drove a larger sized bolt into the floor pan at about a 45 degree angle. This was a pain to get out! Then she found that in the front someone had ripped out the front left mounting point of the drivers seat. To repair the area they used some painters tape (yes you read that correctly!) and a piece of aluminum plate they shoved into the hole to drive another incorrect bolt into. We're still unsure how they got the plate into the hole. but we imagine a BFH was in the mix!

    The crew got the interior pretty well stripped, the bumpers, rear quarter windows and sunroof removed so far and the car really is in shambles. Some may think the Mustang is ready for the junkyard but we see a fresh slate to start over and give this car a new lease on life. Next we hope to get the engine out and start to tackle the body damage. Repair panels are just starting to roll in from CJ Pony Parts and we can't wait to get these quality repair panels installed!

    If you have an idea what we should do for our new engine, please drop us a comment and let us know you're thoughts! Thanks for following, now get out there and build something yourself! -Matt/EW

    Related Eastwood Products:

    • Safety Goggles

      Protect your eyes from hazards from the front or sides; elastic strap

      Click Here To Read Full Post...
  • Eastwood Has a new Project - 1989 Mustang LX 5.0 Project Car

    We regularly brag about the fact that we test, design, and dream up new products in-house here at Eastwood. Testing products requires a good rotation of test vehicles and we've had a number of wrecks we've used in the past. Recently the "powers-that-be" agreed that we should buy a new test vehicle that we could restore as we tested and designed new products. The ideas started flying immediately, "We could` test out a new welding attachment while we replace a rusty lower fender" or "Test a new cleaning product on weathered old vinyl", etc. So the hunt was on!

    1989 Mustang LX 5.0

    After weeks of hunting Craiglist religiously, one of our product developers Joe R. came upon a great deal on a local fox body Mustang for sale. The owner brought it by and we climbed all around it looking for the signs of a good Eastwood project vehicle. Our criteria was like the list of things most would shy away from. We wanted rust, dents, body damage, weathered interior, faded bumpers and paint, etc. Needless to say the seller was a bit confused as we commented on the imperfections the car had "Oh cool, the seats are quite worn!" or "Oh nice, it has been in a fender bender at some point", "Oh look it has some rust in the rockers!". Luckily it wasn't April Fools yet and the seller finally understood why we were acting that way. We struck a deal and the car became ours!

    Mustang LX 5.0

    1989 Mustang LX 5.0

    1989 Mustang LX 5.0

    Fast forward a week and we are now starting to brainstorm where will start on the new addition. We plan to stay pretty conservative in this build, keeping it fairly original (or so we are telling the bosses right now!). But we are always looking for your opinions on what we should do to bring this car back from its beater status! Keep watching the Eastwood Blog as we update on the progression of this Mustang.

      Click Here To Read Full Post...