Tag Archives: fox

    • Project Resolution Phase 3 Teardown

      Since our last post we've been busy working on disassembling the car down to just a rolling shell. This meant we had to removed the entire drivetrain and start deciding if we were going to keep the original or get a replacement engine. The engine and transmission came out pretty easy when using the Folding Engine Hoist. We then separated the engine and transmission and put the engine on a Ford Small Block Rolling Engine Stand so we could easily move it around the shop.

      Meanwhile, some of the other members of the team worked on sanding the fenders and doors down to bare metal using the Eastwood Stripping Discs and then sprayed them with Eastwood Fast Etch to keep them from flash rusting while they wait their turn for bodywork and shiny paint.

      After looking over the engine we decided that this engine had been neglected for quite sometime and even the original waterpump was still on the engine! When Tim went to remove the bolts out of the waterpump just about every single one broke off. This is going to cause a lot more work as we now have to extract each broken bolt. This task will include removing the harmonic balancer on the crank and the timing chain cover to get to the bolts that broke. Let's hope this doesn't require some serious surgery!

      Once we were tired of fighting with broken bolts we moved on to removing the front radiator support on the car. This is NOT an easy job even on the best day. First of all you have to drill out numerous spot welds and the number of spot welds on each side of the radiator support are not equal. It seems like the spot welder in the factory just did however many felt right that day.. or two guys were spot welding on each side and one did way more than the other. The other problem we had was that the car has been hit in the front and some of the metal was bent and damaged. We took turns drilling spot welds with the Eastwood Spot Weld Cutters and slowly we were able to peel the old radiator support off of the front of the car. We'll have to do some hammer and dolly work to the remaining parts on the front end, but so far the CJ Pony replacement radiator panel seems like it will fit pretty well.

      Next up we will have to remove the damaged inner fender skirt panel and mock it all up to make sure the front sheet metal will sit correctly when we're done. Soon we'll be firing up the MIG 175 and the TIG 200 to weld these panels in place. Stay tuned, we're just getting warmed up!

      Related Eastwood Products:

        Click Here To Read Full Post...
    • Project Resolution Becomes a Shell

      We've been VERY busy since our last update. We've decided that the best way to fix the body damage in the inner fender was to remove the 5.0 engine from the Mustang. As we dug in we found all sorts of holes drilled in that side of the engine bay from someone using a slide hammer to pull the dents and never filling the holes. This will be a great time to freshen up and paint the bay while we're "in there".

      Since we made the decision to pull the drivetrain out everyone has been arguing over what we should do when we put an engine back into the car. Some ideas we've heard range from mild to wild! We've heard supercharging, turbo, refresh and bring back to stock, a new crate engine, even a wild naturally aspirated engine build (big cam, port and polish, lightened and balanced internals, etc). We're still undecided, but I admit it would be good fun to see what sort of power we could get out of a cheap custom turbo setup on the stock 302 with Eastwood tools (give that TIG 200 a workout!). So we decided to do a compression test on all eight cylinders in case we keep the engine or use it as a base. Surprisingly all cylinders were pretty close and within spec. With the high being 145PSI and the low being 130PSI, this engine has faired better than many other fox body Mustangs out there!

      Now with those numbers recorded, Nick and I tore into the bay removing everything that needed to come off to remove the drivetrain. We're a little behind schedule, so we pulled out the Eastwood Air Tools to get the job done a little faster. We didn't run into that many rusty or seized bolts, but we were surprised that few we did run into, the Composite Twin Hammer Impact Wrench broke them loose with ease. With the use of the impact wrench and the Eastwood Composite Air Ratchet we have the engine hanging by only a few bolts. We're hoping later this week to try and pluck the lump out of the bay and drop it on the engine stand.

      While Nick and I worked on the engine bay Lisa, Amanda, Kevin, and Randy worked on getting the interior taken apart. This area was as dirty and abused as we expected, but Lisa did find a few surprises when she was removing the drivers seat. It turns out that someone had ripped or destroyed some of the seat mounting locations in the floor and made some pretty unsafe repairs. Under the right rear drivers seat bracket they had stripped out the mounting hole and drove a larger sized bolt into the floor pan at about a 45 degree angle. This was a pain to get out! Then she found that in the front someone had ripped out the front left mounting point of the drivers seat. To repair the area they used some painters tape (yes you read that correctly!) and a piece of aluminum plate they shoved into the hole to drive another incorrect bolt into. We're still unsure how they got the plate into the hole. but we imagine a BFH was in the mix!

      The crew got the interior pretty well stripped, the bumpers, rear quarter windows and sunroof removed so far and the car really is in shambles. Some may think the Mustang is ready for the junkyard but we see a fresh slate to start over and give this car a new lease on life. Next we hope to get the engine out and start to tackle the body damage. Repair panels are just starting to roll in from CJ Pony Parts and we can't wait to get these quality repair panels installed!

      If you have an idea what we should do for our new engine, please drop us a comment and let us know you're thoughts! Thanks for following, now get out there and build something yourself! -Matt/EW

      Related Eastwood Products:

      • Safety Goggles

        Protect your eyes from hazards from the front or sides; elastic strap

        Click Here To Read Full Post...
    • 2013 Eastwood New Years Resolution- Reintroducing our Project Ford Mustang

      1989 Ford Mustang Repair Project

      A while back, we talked about a "Fox Body" Ford Mustang that we picked up off of the local Craigslist with plans of using it to test products and eventually "restore" it.  Since then, we've used it for testing of new products and for a tech video where we restored the original wheels. Otherwise it has sat out in the weather and gotten progressively worse. Now with a dead battery, we need to use the Eastwood Battery Jump Pack to start it.

      1989 Ford Mustang Restoration

      So at the end of 2012, we decided we needed to get in gear and give this car a new lease on life!  Although we have a warehouse full of Eastwood tools, paints, and supplies available to us, we wanted to make this a project that is just like the project you have sitting in your garage.  We've set a budget of $7,000 and a goal of making this Pony cruise-nite ready by mid-summer.   That means, there may be things we'd like to do, but they may have to wait until next winter, if they do not fit into the budget.  Oh yeah, did we mention we will be working on this around our daily jobs at Eastwood, our own projects, etc.....there will be time constraints just like you have when trying to get your project done!

      We're going to need a lot of Eastwood products to bring this tired ol' gal back to life, so we started a list of products we'll be using along the way. Check back often as we list more items we used on the build!

      http://www.eastwood.com/project-resolution-showcase.html

      Check out our evaluation of the car in the video below and watch this space as we start tearing into the car. It's definitely going to get much worse before it gets better!

        Click Here To Read Full Post...