• Home
  • Cylindrical Wire Brush - 5 pack
Cylindrical Wire Brush - 5 pack is rated 3.5789 out of 5 by 19.
Rated 2 out of 5 by from very disappointed with this product i had much higher expectations of this product the arbor for one is made of very cheap metal therefore when you put any kind of pressure on the brush the drill chuck just can't grab the arbor because the metal is way to soft,also you can't bend these brushes at all to get them in tight places i went through three of them in no time and just stopped using them as i felt they are a waste of money maybe i'll find something a little easier to use the remaining two brushes on,they are just not intented for tight spots at all i'm sure eastwood can come up with a better product then this .....
Date published: 2013-11-10
Rated 5 out of 5 by from Worth the money... I bought these to strip a frame on a 68 Bronco that I had lifted the body above. I bought two sets expecting to go through all 10. I was surprised when I only went through four of them! I ran them with my 18v Dewalt drill, a little heavy to hold, but it has good battery life. The brushes did an excellent job cleaning 45 yrs of dirt, rust, and scale. I did have some wire breakage, so standard safety equipment is mandatory.
Date published: 2013-09-21
Rated 4 out of 5 by from Works well but wears down quickly I bought this set of brushes to clean inside the rear frame rails of my '65 Mustang. 40 years of gunk and rust were whisked away quickly and easily. The brushes worked great BUT once they conform to a small space (slightly smaller diameter than a brush) , they stay at the smaller diameter. They do not spring back. Once they loose the original diameter you will need to move on to a new brush if brush size is important for your project. It would be nice if they were made out of a springier material. I would buy these again as they do work great.
Date published: 2013-04-11
Rated 3 out of 5 by from Fair Product- could be better Bought these to help strip down a rear axle beam. On a flat surface these worked well, but trying to fit into a tight spot proved to be a challenge. The brushes came loose in the drill and fell out. Because of the twist in the wire would only work in one direction or the wires could come loose. Would recommend the set include different sizes to work in smaller spaces.
Date published: 2014-03-28
Rated 5 out of 5 by from well worth the money I bought the these brushes to take the rust off of parts that I'm swapping into my 93 fox body mustang... they work better than I had hoped they hold up to the heavy use I need them for and have performed better than all the other methods I've tried...in my opinion the only way too do a better job of removing paint and rust is a media blaster... I highly recommend these for a diy person on a budget
Date published: 2013-07-12
Rated 4 out of 5 by from Very happy with the product I am restoring a 64 Corvair and needless to say it is rusty. I have used the wire brushes on the suspension and on the floor pans of the car. The brushes work better than expected. The end even can become cone shaped to reach into corners. The only darw back keeping it from 5 stars is the shaft. It is twisted wire and does not hold tight in the drill. You have to keep tightening the chuck.
Date published: 2015-01-30
Rated 5 out of 5 by from Well worth the money I purchased the new Cylindrical Wire Brushes and have been very pleased with the results. After receiving the Brushes I tried them on some 1/4" mild Steel Bar Stock before I did some welding. It removed the rust with ease. The Brushes did what I had hope they would do. It's a solid product in my opinion.
Date published: 2013-06-11
Rated 5 out of 5 by from Great Product I am very happy with these brushes. They remove paint with little effort and do a great job on rust. they work is tight spaces and odd shapes. They do not kick back as bad as some brushes and by reversing the drill the kickback can be controlled. They seem to hold up very good. I
Date published: 2013-02-18
  • 2015-03-04T10:23CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_19
  • loc_en_US, sid_13902, PRD, sort_relevancy
  • clientName_eastwood

Would the wires in these be considered "course" (.015" diameter) or "fine" (.01" diameter)?

Asked by: brett45209
Hello, The wires on the cylinder brushes would be considered course.
Answered by: Ed O 88
Date published: 2014-09-12
  • 2015-03-04T11:39CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_13902, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Cylindrical Wire Brush - 5 pack

Item #13902 Brand: Eastwood

Works with your drill to scrape away rust, paint and other coatings

Details

5 Cylindrical Wire Brushes work with your drill to scrape away rust, paint and more with just a pull of the trigger Use these 5 Cylindrical Wire Brushes in your corded or cordless drill to remove rust, paint and other coatings.
  • Clean tubes, pipes, and more
  • Brush section is 2" in diameter, 4" long
  • 6" long overall

More info...

About Cylindrical Wire Brush - 5 pack

5 wire brushes are designed to speed-up the rust and paint removal process on large surfaces, whether flat, contoured or hollow. Use for cleaning tubes, gratings, sleeves and cylinders.


Contents

5 Cylindrical Wire Brushes


Safety

Do not operate your drill faster than 3,000 RPM. Wear safety glasses while using.


Customers also viewed: