• Home
  • Cylindrical Wire Brush - 5 pack
Cylindrical Wire Brush - 5 pack is rated 3.6667 out of 5 by 21.
Rated 1 out of 5 by from Dissapointed with this product The wires on the brush quickly spun off leaving strands all over the place. The core bent easily and created a hazard. Overall, other tools such as wire wheels and sanding discs are better. The concept is great as the length and size will get to areas no other tool can reach.
Date published: 2012-11-06
Rated 4 out of 5 by from neeeds more used it to clean axle tube on 4x4 with extenders made for a drill. Shaft tightened by set screws so no problem having it hold. Could use a few more bristles, but it did the job I wanted it to do. Now if I could just get an answer back on their powder coating gun I bought.
Date published: 2015-03-14
Rated 2 out of 5 by from Overated went thru 5 in under 30 minutes, ok for light surface rust in open areas but tight spots will wipe it out in nothing flat. Not at all what I expected from Eastwood as I use their products Daily. Ok for the money but had bigger plans for them...
Date published: 2012-06-11
Rated 3 out of 5 by from wire brush 5 pack They work good fresh . I used them to clean the inside of my cars frame rails. But as they bend over its slow going and the little wires break off and you find them everywhere. I must say they did the job.
Date published: 2012-05-14
Rated 2 out of 5 by from Don't buy. Wore two out in ten minutes stripping paint and rust from suspension. Wires are not bound tight enough and come loose. Wear your safety glasses because the wires will be flying towards you.
Date published: 2013-06-03
Rated 4 out of 5 by from good product The wire brushes did great. I just needed to ensure that I used the brushes in a non-cordless drill. I need to ensure that I did not put too much pressure on the brush as it would bend.
Date published: 2014-05-08
Rated 3 out of 5 by from light duty only As soon as you put a little pressure on the brush the shaft bends rendering it pretty much useless. Anything more than light duty is beyond this products use.
Date published: 2014-04-09
Rated 1 out of 5 by from waste of money Unless your project is completely flat don't waste your money on this product it will just bent at the drill chuck and become completely useless.
Date published: 2014-12-27
Rated 5 out of 5 by from cylindrical wire brush 5 pack Cleaned the frame of my 08 chevy silverado Did a excellent job, removed any rust I had Like nothing. Very nice and easy to use. Holds up good
Date published: 2013-10-29
Rated 5 out of 5 by from wire brushes a little afraid to buy them cause of some reviews but they worked very good for me!! got the job done.
Date published: 2015-03-03
Rated 5 out of 5 by from this is a good product these need to come in a variety of how coarse they are....less coarse would be nice to have ....
Date published: 2014-06-23
Rated 5 out of 5 by from Eastwood Quality A couple bucks more and you get brushes that last for many uses each. Love them!
Date published: 2014-03-12
Rated 4 out of 5 by from Cylindrical wire brush-5 pcs. Got them and they work fine for what i needed them for. THANKS Bill
Date published: 2015-01-09
  • 2015-04-18T08:57CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_2, bvpage2n
  • co_hasreviews, tv_0, tr_21
  • loc_en_US, sid_13902, PRD, sort_relevancy
  • clientName_eastwood

Cylindrical Wire Brush - 5 pack

Item #13902 Brand: Eastwood

Works with your drill to scrape away rust, paint and other coatings


5 Cylindrical Wire Brushes work with your drill to scrape away rust, paint and more with just a pull of the trigger Use these 5 Cylindrical Wire Brushes in your corded or cordless drill to remove rust, paint and other coatings.
  • Clean tubes, pipes, and more
  • Brush section is 2" in diameter, 4" long
  • 6" long overall

More info...

About Cylindrical Wire Brush - 5 pack

5 wire brushes are designed to speed-up the rust and paint removal process on large surfaces, whether flat, contoured or hollow. Use for cleaning tubes, gratings, sleeves and cylinders.


5 Cylindrical Wire Brushes


Do not operate your drill faster than 3,000 RPM. Wear safety glasses while using.

Customers also viewed: