Dual Voltage HotCoat Powder Gun - Voltage Powder Coating

Cart is Empty

View

Related Products

Check items to add to the cart or select all

MIG175amp-220v Welders with FREE SPOOL GUN ONLY $499.99!

Eastwood Digital Torque Wrenches and Adaptors

Eastwood Pneumatic Tools - Impact Wrench, Metal Sheers, Metal Saw

Recently Viewed Items

Infrared 6000 Curing System

Item #10680
Panel Flanger Set Regular And Extra Wide

Item #31021
Eastwood Copper Weld Thru Primer 16 oz Aerosol

Item #11281 Z

Community Poll

ABOUT SSL CERTIFICATES

Home /
Powder Coating /
Powder Coat Guns /
Eastwood Dual Voltage HotCoat Powder Coating Gun

Dual Voltage HotCoat Powder Gun

Enlarge product image

Eastwood Dual Voltage HotCoat Powder Coating Gun

Item #11676

Only $169.99

Dual-Voltage HotCoat Powder-Coating Gun gives you the most complete coverage from tight areas to large surfaces

With our dual-voltage HotCoat gun, you can powder coat interiors and hard-to-reach corners!

Extremely durable finish
Coat and cure in under an hour!
Easy to apply
Quick color changes
Economical
Versatility with 2 settings
Low 15,000-volt setting
High 25,000-volt setting for multi-coat coverage over larger areas
Increased powder adhesion
Minimal overspray

Either way, you'll get all the benefits of powder coating in your own shop!

9 Review(s) | Add Your Review

Add Items to Cart Qty:

Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

One 8-oz. bottle of powder (not included) covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat powder coating requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).

Includes the Dual-Voltage HotCoat Powder Coating Gun, dual-voltage power supply, activation switch, ground clamp and cable, 1/4" NPT air fitting, and empty 8-oz. bottle.

Accessories

58112 Silicone Cap & Plug Kit
10041Z PRE Painting Prep
19418ZP Fast Etch Rust Remover and Metal Prep
12850 Powder Coat & Paint Dissolver (Gal.)
51558 HotCoat Powder Coating Chip Chart
10421 High-Temp Masking Tape Kit
11476 Compact Infrared Non-Contact Thermometer
10255 Hotcoat Powder High-Tech Color Sample Kit

(Q) How long does the baking process take?
(A) For improved flow out (less "orange peel"), bake coated parts at 500 degreesF until powder flows out (about 3-4 minutes for light sheet metal parts), then turn down the heat to 400 degreesF for a full 15 minutes.

(Q) How can I improve transfer efficiency?
(A) The 10128 HotCoat High-Performance Deflector greatly improves transfer efficiency. Use the Standard Deflector for getting powder in recessed areas.

(Q) What are the electrical requirements?
(A) This HotCoat Gun requires 105-125VAC, 2 amps at 50-60 Hz. Can be used with a voltage transformer such as 220-230VAC to 105-125VAC as long as the transformer can handle 2 amps.

Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh filter cartridges when curing or inspecting flow-out progress.

One Year Manufacturer's Defect Warranty.

Designed, engineered and tested to Eastwood's specifications.

Final product imported.

Dual Voltage Powder Coating System - How To Use Instructions & Troubleshooting Guide

See this product in action!

Customer Reviews

(Posted on 1/1/12) Works fine, but has the usual leak
Review by Phastphil

Quality
Price
Value

Worked as expected, right down to the leak where the barrel attaches to the bottle lid. Since I expected this, I fixed it w/ clear epoxy. Otherwise, the gun works great for large areas, on the High setting.I tried to put a high performance deflector on it, but the emitter is smaller than on the standard gun. I used more epoxy to hold it in place. Haven't tried it w/ the deflector yet, but will very soon. It might not be needed, but I'll find out. Overall, I'm happy with it.

(Posted on 12/18/11) Very Satisfies
Review by GTA89CONV

Quality
Price
Value

Have original system..worked ok. Was looking to have better coverage with less waste. Designed a nozzel for the original that directed powder much better that those that came with system, Using this new....higher voltage system is great. We finished a group of hinges we were using outside on a building. Coverage was quicker, thicker coating, thus much better flow and coverage. Thanks Eastwood, for this product.

(Posted on 12/18/11) Excellent product and value
Review by Dave M

Quality
Price
Value

I was fortunate enough to pick the gun up at a rock bottom sale price and knowing nothing about powder coating was able to knock out great looking parts in notime. I suck at painting and this thing made me look like a rock star

(Posted on 12/14/11) Great buy
Review by Jon-Michael

Price
Value
Quality

Powder gun is amazing!!! works like its suppose to. I totally reccommend anyone to buy this, i have powder coated several parts now!!!

(Posted on 11/26/11) Great item
Review by RadicalRacing

Price
Value
Quality

To be honest I did not think this product would perform the way it did. Really awsome product, despite simple design an low cost materials.However this proves the fact that things dont have to be over- engeneered to work.I now have 4 units, and this makes colorchanges easier. If youhave to change from black to white you have to make sure the gun is ABSOLUTELY clean. One black fragment in the white finish....You do the math.. I have one gun for white,one for clear, and to for all others. -Easy(and looks cool...) I also purchased a lot of bottles so I dont have to empty one to cange colors. Cheap and time saving. I would also recomend 2 steps to better the performance of this gun: 1: I glued the activator switch to the left side of the gun handle. This makes it possible to use the thumb to activate the power. Left hand is then free .
2: I put a thin rubber gasket inside the lid attached to the gun. This makes a good seal, -without it the gun can leak powder through the bottle threads. Summary: I love it!!!