• Home
  • Eastwood Dual Voltage HotCoat Powder Coating Gun
Eastwood Dual Voltage HotCoat Powder Coating Gun is rated 4.3333 out of 5 by 27.
Rated 5 out of 5 by from Get this one. I bought the original gun first, but it leaked powder from the cap and returned it. Since I just got hooked on coating on my options to replace the gun were limited on a system due to my budget. I decided to buy the dual voltage Hotcoat gun. After the first use I was ecstatic the thing did not leak at all. I cannot believe how much better the dual voltage unit is over the original system. My only complaint and it is the same for the original, but the grounding clip is very wimpy. Do yourself a favor, buy this system instead of the original system. For the few extra dollars it costs, it is worth every penny.
Date published: 2011-05-08
Rated 4 out of 5 by from dual voltage powdercoat gun works well! I was very impressed with this gun right off the bat. It's application was smooth and consistant,powder attaching itself much more readily than my first gun which I've owned since around 1991.My only complaint is the chinciness of the ground clamp which fell apart during my first session with the gun. I have since installed the ground clamp from my previous eastwood gun and am off and running again. In closing I would recommend this gun to anyone wanting an affordable powdercoating system. P.S. I'm actually saving on wasted powder with this gun because less powder ends up on my catch paper than with the old gun.
Date published: 2013-03-24
Rated 2 out of 5 by from Don't waste your money I bought the Dual voltage gun and I used it once and the lid was cracked,it leaked more powder then what came out of the end of the gun. I returned it and received another gun and it leaked the same as the first one, I have a glued it and it worked ok for little while, glued it again and now the lid itself is stripped out where the bottle screws on. (still leaks)I would be willing to pay more money for a better product and all they need to do is make the lid out of metal and seal it properley. I am now buying a REAL powder gun and powder from another supplier.
Date published: 2012-07-11
Rated 4 out of 5 by from Not overly impressed so far I ordered this gun to complete a project for a customer. It took three weeks to arrive(Canada). It came without the diffuser on the end of the gun. I talked to support and they said they would mail the part out the next day. When I asked if it could be rushed to me so I could complete the project soon for my customer the reply was 'we will send it regular post, it shouldn't take too long'. Not too happy here with the service and I haven't even tried the item out yet.
Date published: 2013-11-01
Rated 5 out of 5 by from Very Satisfies Have original system..worked ok. Was looking to have better coverage with less waste. Designed a nozzel for the original that directed powder much better that those that came with system, Using this new....higher voltage system is great. We finished a group of hinges we were using outside on a building. Coverage was quicker, thicker coating, thus much better flow and coverage. Thanks Eastwood, for this product.
Date published: 2011-12-18
Rated 5 out of 5 by from Awesome. First powder gun ever owned First time powder-coater here. My dad got me this gun for Christmas while it was on sale. I've been able to do small miscellaneous parts for my car with ease. I didn't have the money to buy an oven off here, so I just found one on craigslist for $20 that cures my projects just fine. Saves me money from doing it elsewhere. Planning on offering it as a service to the local area as soon as space is made in our garage and the sandblasting cabinet is assembled. Couldn't have been happier.
Date published: 2012-03-08
Rated 5 out of 5 by from Great item To be honest I did not think this product would perform the way it did. Really awsome product, despite simple design an low cost materials.However this proves the fact that things dont have to be over- engeneered to work.I now have 4 units, and this makes colorchanges easier. If youhave to change from black to white you have to make sure the gun is ABSOLUTELY clean. One black fragment in the white finish....You do the math.. I have one gun for white,one for clear, and to for all others. -Easy(and looks cool...) I also purchased a lot of bottles so I dont have to empty one to cange colors. Cheap and time saving. I would also recomend 2 steps to better the performance of this gun: 1: I glued the activator switch to the left side of the gun handle. This makes it possible to use the thumb to activate the power. Left hand is then free . 2: I put a thin rubber gasket inside the lid attached to the gun. This makes a good seal, -without it the gun can leak powder through the bottle threads. Summary: I love it!!!
Date published: 2011-11-27
Rated 4 out of 5 by from Works fine, but has the usual leak Worked as expected, right down to the leak where the barrel attaches to the bottle lid. Since I expected this, I fixed it w/ clear epoxy. Otherwise, the gun works great for large areas, on the High setting.I tried to put a high performance deflector on it, but the emitter is smaller than on the standard gun. I used more epoxy to hold it in place. Haven't tried it w/ the deflector yet, but will very soon. It might not be needed, but I'll find out. Overall, I'm happy with it.
Date published: 2012-01-02
  • 2015-04-18T09:00CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_27
  • loc_en_US, sid_11676, PRD, sort_relevancy
  • clientName_eastwood

Hi,  so i had bought your original gun with single voltage. I had issues making a thick coat like I wanted. Is this dual voltage gun help me get a thicker layer of powder onto my part?  Or was i just doing something wrong with my original gun? 

Asked by: dYadlo
I know that it can be only so thick but the amount i was getting was as thin as paint. Little bump would be all the way to metal.
Answered by: dYadlo
Date published: 2015-03-21

Can u paint a full engine and put a heat lamp on it 

Asked by: eric83
Yes you would be able to powder the entire block and cure with a heat lamp
Answered by: SeanA
Date published: 2015-01-20

Approximately how much material would 1 pound of powder cover.

Asked by: Wireman
25sqft
Answered by: SeanA
Date published: 2015-01-20

Do you have a way that you can add your own metal powder to the base product?  Ii would like to use powder coating gun with my own metallic powder. Do you sell the curing material that i can mix my own.

Asked by: tedman
You can add flake or pearl to our powders, but we do not have any way to make custom powders.
Answered by: MikeL
Date published: 2014-12-11

What is the temperature of powered coating and how do you do large parts?

Asked by: GSmitty
Baking process is anywhere from 375-450 degrees depending on the powder. And you would either use an oven and or a curing lamp
Answered by: SeanA
Date published: 2014-12-02

Hi, Can I know the total weight of this equipment ?  Thanks!

Asked by: aniBedre
5lbs total weight (without powder in the container and including the power box)
Answered by: SeanA
Date published: 2014-12-02

Is this a corona type gun

Asked by: Jlowe
This is a corona type gun.
Answered by: NickC
Date published: 2014-11-18

Need to finish vintage car starter, generator etc in reflective chrome. Debating on powder coating or copy chrome plating. Also bare metal coat a cast aluminum intake. Will these coatings hold up on engine parts?

Asked by: JimB
Yes the powder will hold up to most of all engine parts minus exhaust manifolds/headers/heads
Answered by: SeanA
Date published: 2014-10-28
  • 2015-04-18T09:20CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_US, sid_11676, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Eastwood Dual Voltage HotCoat Powder Coating Gun

Item #11676 Brand: Eastwood

2 voltage settings allow complete coverage--tight spots to large areas

Details

Dual-Voltage HotCoat Powder-Coating Gun gives you the most complete coverage from tight areas to large surfaces With our dual-voltage HotCoat powder coating gun, you can powder coat interiors and hard-to-reach corners!
  • Extremely durable finish
  • Coat and cure in under an hour!
  • Easy to apply
  • Quick color changes
  • Economical
  • Versatility with 2 settings
  • Low 15,000-volt setting
  • High 25,000-volt setting for multi-coat coverage over larger areas
  • Increased powder adhesion
  • Minimal overspray

Either way, you'll get all the benefits of powder coating in your own shop!

More info...

About Eastwood Dual Voltage HotCoat Powder Coating Gun

The Dual Voltage HotCoat gun is one of the best powder coating guns on the market today. Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

One 8-oz. bottle of powder (not included) covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat powder coating requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).


Contents

Includes the Dual-Voltage HotCoat Powder Coating Gun, dual-voltage power supply, activation switch, ground clamp and cable, 1/4" NPT air fitting, and empty 8-oz. bottle.


Specs

Accessories

58112 Silicone Cap & Plug Kit
10041Z PRE Painting Prep
19418ZP Fast Etch Rust Remover and Metal Prep
12850 Powder Coat & Paint Dissolver (Gal.)
51558 HotCoat Powder Coating Chip Chart
10421 High-Temp Masking Tape Kit
11476 Compact Infrared Non-Contact Thermometer
10255 Hotcoat Powder High-Tech Color Sample Kit


FAQs

(Q) How long does the baking process take?
(A) For improved flow out (less "orange peel"), bake coated parts at 500 degreesF until powder flows out (about 3-4 minutes for light sheet metal parts), then turn down the heat to 400 degreesF for a full 15 minutes.

(Q) How can I improve transfer efficiency?
(A) The 10128 HotCoat High-Performance Deflector greatly improves transfer efficiency. Use the Standard Deflector for getting powder in recessed areas.

(Q) What are the electrical requirements?
(A) This HotCoat Gun requires 105-125VAC, 2 amps at 50-60 Hz. Can be used with a voltage transformer such as 220-230VAC to 105-125VAC as long as the transformer can handle 2 amps.


Safety

Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh filter cartridges when curing or inspecting flow-out progress.


Warranty

One Year Manufacturer's Defect Warranty.

Designed, engineered and tested to Eastwood's specifications.

Final product imported.


Instructions

Click here for instructions


Customers also viewed: