- Eastwood Dual Voltage HotCoat Powder Coating Gun
Eastwood Dual Voltage HotCoat Powder Coating Gun
Item #11676 Brand: Eastwood
- Extremely durable finish
- Coat and cure in under an hour!
- Easy to apply
- Quick color changes
- Versatility with 2 settings
- Low 15,000-volt setting
- High 25,000-volt setting for multi-coat coverage over larger areas
- Increased powder adhesion
- Minimal overspray
Either way, you'll get all the benefits of powder coating in your own shop!
About Eastwood Dual Voltage HotCoat Powder Coating Gun
The Dual Voltage HotCoat gun is one of the best powder coating guns on the market today. Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.
One 8-oz. bottle of powder (not included) covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat powder coating requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).
Includes the Dual-Voltage HotCoat Powder Coating Gun, dual-voltage power supply, activation switch, ground clamp and cable, 1/4" NPT air fitting, and empty 8-oz. bottle.
58112 Silicone Cap & Plug Kit
10041Z PRE Painting Prep
19418ZP Fast Etch Rust Remover and Metal Prep
12850 Powder Coat & Paint Dissolver (Gal.)
51558 HotCoat Powder Coating Chip Chart
10421 High-Temp Masking Tape Kit
11476 Compact Infrared Non-Contact Thermometer
10255 Hotcoat Powder High-Tech Color Sample Kit
(Q) How long does the baking process take?
(A) For improved flow out (less "orange peel"), bake coated parts at 500 degreesF until powder flows out (about 3-4 minutes for light sheet metal parts), then turn down the heat to 400 degreesF for a full 15 minutes.
(Q) How can I improve transfer efficiency?
(A) The 10128 HotCoat High-Performance Deflector greatly improves transfer efficiency. Use the Standard Deflector for getting powder in recessed areas.
(Q) What are the electrical requirements?
(A) This HotCoat Gun requires 105-125VAC, 2 amps at 50-60 Hz. Can be used with a voltage transformer such as 220-230VAC to 105-125VAC as long as the transformer can handle 2 amps.
Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh filter cartridges when curing or inspecting flow-out progress.
One Year Manufacturer's Defect Warranty.
Designed, engineered and tested to Eastwood's specifications.
Final product imported.
Customers also viewed:
Try powder-coating at home! Includes original gun, 4 colors and moreOnly $149.99
Kit includes our Dual-Voltage Gun, gloss black powder and more!Only $209.99
11,000-volt gun brings benefits of powder-coating to your home shopOnly $99.99