• Home
  • Eastwood Dual Voltage Powder Gun Starter Kit
Eastwood Dual Voltage Powder Gun Starter Kit is rated 4.5 out of 5 by 24.
Rated 4 out of 5 by from Works really well if you follow this. I bought this kit for my buggy project. I tryed it recently, and adjusted the gun to the exacts specs, (10 psi max and about 5 cfm) if you stick to about 5 CFM you notice that the powder goes in very little cracks (as a can would do) and very low powder loss. and the result is amasingly tought.
Date published: 2014-03-03
Rated 5 out of 5 by from Great gun for the price. My first powder coat gun was a cheap HF model. It guess you could say it worked… if by worked you mean you actually intended to powder coat your spray booth instead of the part. I saw a YouTube video of a guy using the Eastwood dual voltage setup and when I saw it was on sale I figured I'd give it a try and I'm very glad I did. What a pleasure it is to use a gun that actually lays the powder where you want it. Very easy to use with no puffing like with the HF gun. The dual voltage didn't appear to me to make any difference but that may have been due to the fact that the part I was powder coating didn't have any areas prone to the Faraday Effect. Overall a great gun for the price and the extras that came with it were just the icing on the cake. I also love the way the Eastwood powder comes in plastic containers that screw right onto the gun. I would highly recommend this gun to anyone just starting out or even experienced powder coaters looking for an extra knock around gun, but don’t knock too hard… it’s a wee bit fragile.
Date published: 2014-08-06
Rated 2 out of 5 by from Dual voltage not worth the extra money I have been coating for some time using a Harbor Freight purchased system, I was not satisfied with the capability of coating crevices and recessed areas. So I purchased the Eastwood dual voltage system for the higher voltage setting to assist with this issue. After using the new kit I found that the higher setting did not provide any noticeable benefit over the lower setting. The coating system performed just as well as the Harbor Freight system, but at more than double the price. I feel as if the purchase was not worth the money and I would have been better off continuing the use of my Harbor Freight system or purchasing a higher end system. If your looking to get a powder coating system stick to the single voltage system offered by Eastwood (which my brother has and likes) here or purchase the coating system from Harbor Freight. Also the ground strap leaves a lot to be desired. I would recommend replacing it.
Date published: 2013-08-20
Rated 5 out of 5 by from best purchase ever if you do your homework you will find this product is the best one for do it yourself guys and gals and the results are super high quality finishes that last ...normal paint was not for me... this has been on my list for my shop to purchase for a long time and as soon as I received it I put it to use and love the results ...thanks eastwood
Date published: 2013-04-20
Rated 5 out of 5 by from Dual Voltage Powder Gun Starter Kit This was my first time powder coating anything. This kit is pefect for a beginner. I tried reflective chrome first and I am very pleased with the results. Prep is the key, before and after pre heating. I will recommend this kit to anyone starting for the first time. Thank you Eastwood.
Date published: 2011-12-22
Rated 4 out of 5 by from a great gun This is a perfect unit for the beginner. It works very well and is 100% worth the amount charged. My first time powder coating went extremely well and am ready to offer this service to others wanting a great shine for a reasonable price. Thanks Eastwood for what you do. Brad in Canada
Date published: 2013-03-05
Rated 5 out of 5 by from Great Gun We bought the original gun about a year age which work good. Decided to buy the Dual Voltage to help with top coats sure makes the job easier with a much better coverage. Used it for both the clear over the smoke chrome and translucent Blue over chrome with excellent results.
Date published: 2014-06-16
Rated 4 out of 5 by from Gun works great The gun works good, just wish the powder adheared better. I feel like 1/4 of the bottle ended up on the floor, no matter what wetting I had it on. So far the biggest thing I did was a gas tank and it came out perfect!
Date published: 2013-07-31
Rated 4 out of 5 by from Very good start up tool I was very pleased with this equipment, it was easy to set up and start using. My first powder coating experince was a good one. I would like for the dual voltage switch to be lighted.
Date published: 2013-05-08
Rated 5 out of 5 by from awesome kit for the price great finish, great results would recommend this kit to anyone who wants to get started powder coating
Date published: 2011-12-08
Rated 5 out of 5 by from Great addition to my shop Having never painted anything before this was easy to use and my sculptures look great!
Date published: 2013-03-01
Rated 4 out of 5 by from Nice powder gun system This is my third Eastwood powder gun system First one lost in shop fire. Second one I just wore it out. And now I have got the new dual voltage gun, because I know how good the first two were. Have not used this one yet do to building new items to coat. But I am sure this will be as good if not better than the last two. If you are considering doing this, go crazy and have fun.
Date published: 2014-11-21
Rated 5 out of 5 by from Great Product This system works very well. I had not tried powder coating but had seen it done in a commercial facility. The results are just as good and easy for a novice to accomplish following the supplied directions in a home workshop. The finished parts come out great and equal in quality to a large commercial job at a fraction of the cost and to your own likes.
Date published: 2014-10-28
Rated 5 out of 5 by from excelent value I upgraded from a Chicago Pneumatic machine. The efficiency is much greater, much more even powder dispersion, great powder attraction. Perfect for the at home hobbyist.
Date published: 2015-03-05
Rated 5 out of 5 by from Easy to use I bought this gun and love it been going crazy powdering everything, very easy to use and powder is so durable. Would recommend to anyone
Date published: 2015-02-28
Rated 5 out of 5 by from easy to use and great product didn't have a clue what I was doing and shot some powder and it turned out awesome. Love it. Must have item. Never use a spray can again.
Date published: 2015-03-13
  • 2015-03-31T10:24CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_2, bvpage2n
  • co_hasreviews, tv_0, tr_24
  • loc_en_US, sid_11698, PRD, sort_relevancy
  • clientName_eastwood

What size of air compressor do you need for this powder gun starter kit? 

Asked by: Boogie
  • 2015-03-30T10:29CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_2, bvpage2n
  • co_hasquestions, tq_9
  • loc_en_US, sid_11698, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Eastwood Dual Voltage Powder Gun Starter Kit

Item #11698 Brand: Eastwood

Kit includes our Dual-Voltage
Gun, gloss black powder and more!

Details

Our best value! HotCoat Powder-Coating Starter Kit includes our Dual-Voltage gun for greater versatility With our dual-voltage HotCoat powder coating gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop! Besides the dual-voltage gun, this kit also includes gloss black color, plus all the other powder coating supplies else you'll need (except compressed air and a dedicated oven) to achieve expert results.
  • Extremely durable finish
  • Coat and cure in under an hour!
  • Easy to apply
  • Quick color changes
  • Economical

More info...

About Eastwood Dual Voltage Powder Gun Starter Kit

Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the over-sprayed powder. Contains no environmentally harmful solvents. HotCoat Powder Coating System requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).

(See "Contents" tab for all the specific powder coating supplies included in this Dual-Voltage kit.)


Contents

11676 Eastwood Dual-Voltage HotCoat Gun
1/2-lb. Black Gloss Powder
51558 Powder Chip Color Chart
10078 Reusable Hi-Temp Silicone Plugs
10027 Hi-Temp Masking Tape (1/2" x 36-yard roll)
43045 1-lb. Stainless Steel Hanging Wire
34066 In-Line Air Filter
3 Empty Powder Bottles with Screw-On Tops


Specs

Accessories

10041Z PRE Painting Prep
51081 Metal Wash Metal Prep
19418ZP Fast Etch Rust Remover and Metal Prep
20473 2-Stage Air Dryer System
58111 Pack of 20 Hooks
58112 Silicone Cap & Plug Kit
11477 Infrared Thermometer
10590 Infrared Curing Lamp


FAQs

(Q) Can I use my household oven?
(A) No, you cannot use an oven that will be used to cook/bake food.

(Q) How long do I bake/cure the part?
(A) 20 minutes at 400 degreesF.

(Q) Can I remove the powder coating?
(A) Yes, use 12849 Powder Coat & Paint Dissolver (Qt.) or 12850 Powder Coat & Paint Dissolver (Gal.) .

(Q) How do I know what the colors will look like?
(A) Order Eastwood's 51558 HotCoat Powder Coating Chip Chart (free in our kits).


Safety

Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh cartridges when curing or inspecting flow-out progress.


Warranty

1-year mfr's. warranty against defects.

Designed, engineered and tested to Eastwood's specifications.

Final product imported.


Customers also viewed: