• Home
  • Eastwood 12 Inch Slip Roll
Eastwood 12 Inch Slip Roll is rated 2.75 out of 5 by 4.
Rated 3 out of 5 by from useful tool The roller work pretty well but the biggest problem was with the handle.It is about .100" too large and I just wound up using a cresent wrench to turn it. Not a big deal but the handle had to be ground down to clear the upper roller. Is no one looking at this? That is Not a quality fit. And one adjustment screw had a broken plastic handle on arrival and I replaced that with a long 10mm set screw. I have purchased some nice tools from Eastwood but I think they should take a little closer look at this item.
Date published: 2013-12-09
Rated 3 out of 5 by from It works The quality is about what I would expect from a $200 roller. One of the knobs was broken when it arrived and the Handle does not fit very well. If you can look past some of the quality issues it is not a bad buy. It does roll nicely when adjusted correctly.
Date published: 2013-10-04
Rated 1 out of 5 by from junk rollers bent,will not roll evenly.handel must be for something else,1/2 inch square drive for a 3/8 square shaft.han to grind down outer handel to allow clerance to upper roller.CANNOT REMOVE ROLLED ITEM WITHOUT REMOVING HANDEL.JUNK
Date published: 2013-02-03
Rated 4 out of 5 by from Does the job! This slip roll is convenient and solid enough to do what I want with aluminum for my airplane. The secret is the practice pieces. I have to do three or more practice rolls before I get it right, and then can use the actual piece. I even rolled the top of my fuel tank in the shape of a cone, but had to do many strips (one on each end) to get the curvature right.. -
Date published: 2013-06-25
  • 2015-03-02T10:11CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_4
  • loc_en_US, sid_14041, PRD, sort_relevancy
  • clientName_eastwood

will this roll 2 inch wide 1/8" strap?

Asked by: Bryan Jondes
No, the maximum thickness is 20 gauge steel.
Answered by: MikeL
Date published: 2015-02-18
  • 2015-03-02T11:55CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_14041, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Eastwood 12 Inch Slip Roll

Item #14041 Brand: Eastwood

Create bends, cones, and cylinders
Heavyweight Item - Special shipping charges may apply.

Details

This Eastwood 12 Inch Slip Roll can help you recreate a variety of parts including rocker panels, and any other piece of sheet metal requiring a rolled bend. Designed for use on sheet metal and wire to create
  • Bends
  • Cones
  • Cylinders

More info...

About Eastwood 12 Inch Slip Roll

This Eastwood 12 Inch Slip Roll was designed for use on sheet metal and wire to create bends, cones, and cylinders. This too can help you recreate a variety of parts including rocker panels, and any other piece of sheet metal requiring a rolled bend.


Accessories

28187 Bead roller with 6 mandrel sets,
51088 DIY Shrinker/Stretcher Complete set,
13475 Eastwood Electric Metal Shears,
11797 Throatless Shear,
14042 Versa Bend Sheet Metal Brake


FAQ's

Maximum Roll Length 12 Inch,
Minimum Roll Diameter 1 Inch,
Maximum Thickness(Steel) 20 Gauge,
Maximum Thickness (Aluminum), 17 Gauge
Wire Forming Sizes 5/64 Inch, 1/8 Inch, 5/32 Inch
Weight 35lbs,
Overall Dimensions 23 Inch x 63/4 Inch x 9 1/2 Inch


Safety

This tool is considerably heavy. Use extreme caution when mounting in a vice or other temporary fixturing arrangement.Personal injury could occur if tool is dropped. Pinch Hazard. Keep fingers and away from moving parts when operating. Wear appropriate work gloves and protective clothing. Sheet metal will often have sharp edges which can cause cuts to hands and arms. Wear appropriate eye protection. Metal chips can be ejected during the bending process.


Instructions

Click here for product instructions


Customers also viewed: