• Home
  • Eastwood Rat Rod Satin Black Paint

    Eastwood Rat Rod Satin Black Paint

    Item #21857ZP Rat Rod Satin Black Paint

    Give your "rat rod" that perfect satin-black finish; with activator

    Details

    Eastwood's premium Rat Rod Satin Black Single-Stage Acrylic Urethane Topcoat provides exceptional long-lasting beauty and durability.

    Some project rods just won't look finished until you've put on that distinctive, satin car paint finish. Our Rat Rod paint is the only way to go! This premium 2-component topcoat system is blended with top-quality raw materials and advanced composition coatings technology. Superior to acrylic, alkyd and lacquer coatings. Eastwood's single-stage urethane paints hold their gloss longer and won't yellow.

    • 96-fl.-oz. Rat Rod Flat Black Automotive Paint
    • 32-fl.-oz. Activator required (included in 21857)
    • Catalyzed urethane for unsurpassed durability
    • Highly resistant to UV rays, chemicals, chips

    About Eastwood Rat Rod Satin Black Paint

    Sure, some like to "drive her in primer", or opt for a quick "rattle-can" paint job, but this activated, single-step acrylic urethane Rat Rod car paint is a smarter and much longer-lasting choice! Mix 3:1 with activator; no further reduction required.

    Due to regulations pertaining to recycling, we are unable to ship this product to Alberta, Canada.


    Contents

    Choose from the following:
    21857ZP is the Rat Rod Flat Black Single-Stage Urethane Topcoat, Gallon, with Activator; enough to coat the outside of most cars
    21855ZP is the Rat Rod Flat Black Topcoat, Gallon, without Activator
    51379ZP is the Rat Rod Flat Black Topcoat, 1-qt. can, with 8-oz. Activator
    21856ZP is the Eastwood Urethane Activator, 32-oz.


    Application

    Clean surfaces of all contaminants. Abrade surface to be painted with a minimum of 320-grit sandpaper, working up to a 600-grit for maximum adhesion. Re-clean surface. After shaking paint, mix 3 parts paint with 1 part activator. Use caution mixing materials as paint may begin to gel after 2 hours at 70°F. HVLP gun setting: 8-10 PSI, with a 1.4mm-1.8mm tip. This color is formulated to give complete coverage in 2-3 coats. Allow 10 minutes flash time between coats; should be tack-free in 45-60 minutes, with full cure in 18 hours.


    Accessories

    10194ZP PRE Painting Prep, Quart
    51605 Concours HVLP Paint Gun Kit
    51686 Concours HVLP Detail Gun
    20474 4-Stage Dry Air System
    50040ZP Master Paint Prep Kit
    51561Z 6" Liquid Ice Buffing Kit
    34053 Hobby Air Fresh-Air System
    51559 Digital Regulator
    50244ZP Epoxy Gray Primer, Gallon
    50245ZP Epoxy Primer Catalyst, Gallon
    50240ZP 2K Urethane Gray Primer, Gallon
    50241ZP 2K Urethane Primer Catalyst, Quart


    FAQs

    (Q) How much paint do I need?
    (A) Typically one gallon per car. If you are also painting jambs, under the hood, or the trunk, use 2 gallons. For large cars and pickup trucks, use 2 gallons. Number of coats, prep and application methods will affect the amount of paint required.


    Product Information Sheet

    Click here to view product information sheet


    Safety

    Always wear proper eye, skin and respiratory protection. Always paint in a well-ventilated area away from sparks and open flame. Consult MSDS and product data sheets for proper safety precautions.


    Customers also viewed: