- Eastwood Rust Encapsulator Black Aerosol 15 ounce
I have a 72 blazer, I had the body shop primer the body 2 years ago and there are small rust spots bleeding thru the primer now. Would this product work to spray directly over the rust spots to keep them from bleeding thru when it gets painted?
I am going to use this on inside of a 64 Impala fender. Will I be able to apply a DTM Epoxy Primer over encapsulator? I will not be shooting any color over primer, but will be applying an undercoating.
Is there any restriction to ship the rust encapsulator by air mail? I need to send a quarter overseas.
What is the best products to use inside a 55 chevy truck door to treat and stop existing rust?
I have two questions. For surface rust on previously painted automotive sheet metal, is the encapuslator or the converter the best product? What is the recommended time frame between the recommended product and applying an epoxy primer?
How well does the rattle can spray in the horizontal orientation? i.e. spraying the underside of a vehicle. Or should I be considering using a paint brush application?
I forgot to shake the can and the black color had separated. I applied it and it went on clear. Only after did I realize it wasn't mixed. Do I need to reapply?
I am in the process of body work on a 1977 Datsun 620. I was wondering if I could paint the truck with your rust encapsulated and then use one base paint over it
Eastwood Rust Encapsulator Black Aerosol 15 ounce
Item #16060Z Brand: Eastwood
TWICE the corrosion resistance!
Stop rust in its tracks! Our Rust Encapsulator has been reformulated with TWICE the corrosion resistance!
- Twice the corrosion resistance of our original formula for greater durability (tested to 500 hours in a salt-spray chamber)
- Epoxy-fortified for better adhesion and topcoat compatibility
- Penetrates deeper to prevent rust from spreading or forming, even in hard-to-reach areas
- Cures faster, and the low-VOC formula is acceptable in California
- 15-oz. aerosol covers about 10 sq. ft.
- As seen on "My Classic Car" TV show
You thought it was good before...wait ’til you try this great anti-rust spray, the Rust Encapsulator! It seals and stops rust and corrosion from spreading, but it performs even better than our original formula. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability.
About Eastwood Rust Encapsulator Black Aerosol 15 ounce
Eastwood Rust Encapsulator has been tested by an independent lab to be the most effective protection from rust yet. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability. One 15 oz. net wt. aerosol covers about 10 sq. ft. Contains no isocyanates. Heat resistant up to 400' F. Made in the USA.
One 15 ounce net wt. aerosol, enough to cover up to 10 square feet.
Heavy-duty Anti Rust Qt. (16017 Z P) is actually superior for applying into blind areas such as box sections where little or no surface prep can be done. Buy 3 or more and SAVE!
Rust Encapsulator can be applied with the Undercoating System, but this application isn't recommended because Rust Encapsulator requires surface to be free of grease, oil, and loose rust. The best product to coat inside box sections is the Heavy Duty Anti-Rust (16017ZP). This waxy, oily product flows into pinch welds & through rust to seal surface from contact with moisture & air, but cannot be painted over so is only suitable for inside box sections that don't show. Use lacquer thinner for cleanup.
Work in a well ventilated area when applying this product. The use of a respirator like our Professional Respirator (34029) is recommended when applying this coating. Shake vigorously for 2 mins before spraying !!
Made in the USA.
Wire Brush to remove loose rust, scale and paint. Remove dust, grease, oil deposits. Shake can for at least 2 mins after mixing ball starts to rattle. Feather surrounding paint with 220 grit sandpaper. Apply Rust Encapsulator can 10-12" from surface. Single coats dry to the touch in 20 minutes and are thoroughly dry in 3-4 hours at 68 degrees F. For greater durability a second coat can be applied one hour after the first. Allow 6-8 hours after last coat before applying top coat. See can label for more details.
Accessories & Consumables
In places where little or no surface prep can be done, our Heavy-Duty Anti-Rust (16017ZP) is actually a better choice for applying into blind areas such as box sections. Buy 3 or more quart cans and save!
Questions & Answers
Customers also viewed:
Leaves de-rusted metal ready to paint or powder-coat; liquid or gel
Starting at: $14.97
Removes silicone, wax, polish, grease; promotes paint/powder adhesion
Starting at: $6.97
The perfect lacquer paint to match the OEM finish under the hood