• Home
  • Eastwood TIG 200, Plasma Cutter 60 and Cart Kit
Eastwood TIG 200, Plasma Cutter 60 and Cart Kit is rated 3.0 out of 5 by 4.
Rated 5 out of 5 by from Good buy I purchased the 175 mig as well as this 200 amp TIG and 60 amp plasma, order went well items showed up well packaged and no damage from shipping, cart went together well and was a little better cart than the one that came with the mig welder, once cart was assembled welder and torch went on the cart hooked up to the gas and fired up to test them out, the tig welded great, it had been a while since I had done any tig welding so the welds were not the smoothest but that was not the welders fault, have not tried AL yet. Plasma worked fine still getting used to that as well since I am a torch guy never used a plasma but I cut some 1/4" plate I had laying around and cut that like butter. I would recommend these items to any one looking, way cheaper than any of the big three with a 30 day money back and 3 year warranty I could not see how I could go wrong, very happy with this purchase.
Date published: 2014-03-27
Rated 2 out of 5 by from Bad units First the regulator leaked and wasted an entire bottle of gas, second there was no 110 v adapter, lastly after weeks of waiting and when we finally got a new regulator and cord, we hooked everything up and found that the unit was defective and all it does is show overload. This unit was supposed to be for a school my son is taking but now he's a month behind because he hasn't had a working welder.
Date published: 2014-04-21
Rated 4 out of 5 by from Great value for an intermittent use rig We've had ours for over a year and it works well. The only gripe is the where the foot pedal cables enter their connectors. The stress relief fit is poor making them easy to damage if you are not continuously careful with them. Otherwise, it all works well and the results are great.
Date published: 2014-12-27
Rated 1 out of 5 by from Cheap foreign made welder I bought this setup expecting a lot better product. Unfortunate for me, I bought a new house so when I finally set it up and used it , it was too late to return. Waste of $1,500.
Date published: 2015-01-18

Is the #20030 available with foot and hand control

Asked by: lenk
Our TIG welders come with both variable amperage foot pedals and finger switches on the torch. You can select which you'd prefer to use.
Answered by: MikeL
Date published: 2015-01-05

do you sell the protection cover for this?

Asked by: tucky
We do not currently sell a cover specifically designed for the TIG machines.
Answered by: MikeL
Date published: 2014-12-16

How hard is it to get parts for one of these

Asked by: butler75
If you encounter any issue during the warranty period, simply call or email the Tech Department and we will get you taken care of with any parts you might need. After the warranty, or at any point, most parts are available for purchase through our Customer Service Department.
Answered by: MikeL
Date published: 2014-11-20

Is there a way to use stick with this unit

Asked by: Vailcomp
No it is strictly TIG.
Answered by: SeanA
Date published: 2014-11-14

Hello. Can I use this equipment in a machine shop, I need to cut steel and aluminum of 1/2 inch average. This product is free shipping.

Asked by: Ceballos
The Versa-Cut Plasma Cutter will cut up to 7/8" thick. It can handle the 1/2" material with no issues.
Answered by: MikeL
Date published: 2014-11-28

Are theses units designed for home or recreational use? Or can they support the work load of a full shop? 

Asked by: HotRodder45
They are designed to be able to be affordable for the DIY guy while being able to keep up with a shops work flow. A few performance and fabrication shops in our area are using our units as well.
Answered by: SeanA
Date published: 2014-10-28

made in what country?

Asked by: lightning
The units are made to Eastwood specs in China. Both units are backed by Eastwood's 3 year warranty.
Answered by: NickC
Date published: 2014-11-29

Eastwood TIG 200, Plasma Cutter 60 and Cart Kit

Item #20030 Brand: Eastwood

Eastwood TIG 200, Plasma Cutter 60 and Cart Kit
Heavy Item - Special shipping charges may apply.

Details

Save BIG money when you get our TIG 200 Welder PLUS our Versa-Cut 60 Plasma Cutter, and organize it all on the Cart included! Click on the individual links below for all the specs, but you must click the "Buy Now" button below to get the special savings over individual prices! Eastwood-engineered TIG 200 AC/DC Welder offers professional-quality TIG welding at an affordable price!
  • Operates on either 110vAC, 15-amp circuit or 220vAC, 30-amp circuit
  • 1/4"-thick welding capacity
  • High-frequency start for precise arc control
  • Square-wave inverter for accurate aluminum welding
The Eastwood Versa Cut 60 Plasma Cutter works with 220v input to easily slice through steel and non-ferrous metals up to 7/8" thick.
  • 220v AC input
  • 20' torch cable; 10' ground cable with clamp
  • Rated 60-amp output
  • Air flow rate: 5-7 CFM at 20-60 PSI
Our Multi-Unit Welding Cart is designed specifically to keep all your Eastwood welding and cutting equipment and accessories organized.
  • Top shelf holds the TIG-200 welder (or either of our MIG welders)
  • Bottom shelf holds the Versa-Cut 60 Plasma Cutter
  • Middle shelf is for accessory storage
  • Gas-bottle mount includes a TIG rod holder

Click here for welder warranty information


More info...

About Eastwood TIG 200, Plasma Cutter 60 and Cart Kit

TIG200 Welder
Weld it all with the Eastwood TIG200 200AMP welder! The TIG200 features an AC/DC switch that allows both steels and aluminum to be welded with the same machine. With a 14' torch and a 10' ground cable, you'll be able to get into any space with this exceptional machine. It has pre/post flow adjustment knobs to protect your weld and torch. If that's not enough, it even has a foot pedal to control amperage so you can get going quickly and not need to dial-in the machine for a specific material. Included is the TIG200, torch, ground cable/clamp, regulator/hose, and is powered through a NEMA50 plug.

Plasma Cutter
This innovative, affordable, plasma cutter was designed and developed by Eastwood's own R&D staff, and tested in-house on the same type of real-life projects you'll use it for. Works with any standard home- or shop-type air compressor within a range of 20-60 psi; internal moisture separator ensures dry air is delivered to the torch. Rated 220 volts AC, 60 amps. Duty cycle: 60% at 60 amps. Weighs less than 40 lbs., for easier portability. Multi-Unit Cart
This welding cart was designed by to make storage, accessibility and maneuverability of your welder and cutter easier than ever before. This cart incorporates a top shelf which will hold our MIG135, MIG175 or TIG-200 welder. The bottom shelf will store your Versa-Cut Plasma Cutter, while the middle shelf allows storage of necessary welding accessories. The Gas Bottle Mount even incorporates a TIG Rod Holder to store up to 6 different tubes of filler rods. Assembles with simple hand tools.

What is "Plasma Cutting"? Plasma cutting utilizes a high-velocity jet of ionized gas (plasma) that conducts electricity from the torch of the plasma cutter to your metal workpiece. That directed plasma stream (about 30,000° F) heats the workpiece, converting the metal to molten slag. That high-velocity stream literally blows the molten metal away, leaving a clean, precise cut.


Contents

TIG200 Unit
Shielding Gas Regulator
Shielding Gas Hose
Ground Cable with Clamp (10ft)
TIG Torch (17 Series) which accepts industry standard cups, collets, and collet bodies (14 ft.)
Foot Pedal for Amperage Control
110v-to-200v Adapter Plug
Manual
Hand Held Shield
Hammer/Brush
#7 Cup (7/16"), #6 Cup (3/8"), #5 Cup (5/16")
Long Back Cap, Short Back Cap
3/32" Collet Body, 3/32" Collet, 1/16" Collet, 2.0mm Collet
2.0mm Red (Thoriated Tungsten)

Versa-Cut 60 Plasma Cutter
Torch Assembly
Ground Clamp Assembly

Welding Cart
Assembly Instructions


Accessories

13953 Tig consumable kit gets you started with the correct electrodes TIG Welding Cart
Auto-Darkening Welding Helmet
Welding Jacket
Large View Auto-Darkening Helmet
Welding Gloves

Consumables

1/6-inch Collet Body
3/32-inch Collet Body
TIG Torch Rear Back Cap
3/8 Inch Diameter Ceramic Nozzle for TIG-200
7/16 Inch Diameter Ceramic Nozzle for TIG-200
1/16 Inch Diameter Torch Collet for TIG-200
3/32 Inch Diameter Torch Collet for TIG-200
1/16-inch by 36-inch 1 Pound Tube of ER70S-2 TIG Wire
3/32-inch by 36-inch 1 Pound Tube of ER70S-2 TIG Wire
1/16-inch by 36-inch 1 Pound Tube of 4043 Aluminum TIG Wire
3/32-inch by 36-inch 1 Pound Tube of 4043 Aluminum TIG Wire
1/16-inch by 36-inch 1 Pound Tube of 308L Stainless Steel TIG Wire
1/16-inch by 36-inch 1 Pound Tube of 308L Stainless Steel TIG Wire
3/32-inch Diameter 2 Piece Green Tungsten for Steel
1/16-inch Diameter 2 Piece Red Tungsten for Steel
3/32-inch Diameter 2 Piece Red Tungsten for Steel
2 Pack Stainless Steel Scratch Brush


Safety

Always follow welding and cutting safety procedures by wearing face, hand and arm protection. Always wear a minimum #10 shade helmet with TIG and #4 with Plasma Cutter.


Warranty

Click here for welder warranty information Imported.


Application

cutting, welding


Instructions

TIG

Click here for-instructions


Plasma Cutter

Click here for product instructions


Customers also viewed: