• Home
  • Eastwood 2K Urethane Primer Surfacer Gray- Gallon 4:1
Eastwood 2K Urethane Primer Surfacer Gray- Gallon 4:1 is rated 4.8667 out of 5 by 15.
Rated 4 out of 5 by from A bit of a learning curve for the beginner. Goes on a little thicker than the spec sheets indicate. Comparing it to the other Eastwood products, this does not perform exactly as the spec sheets would indicate. It is bit more viscous and requires a 1:2 needle in the Concours Eastwood Gun or to open the needle all the way on a gun with a 1:4. All other adjustments on the gun should be open as well and dialed in as needed. I recommend you use 25 psi at the gun to start if you have a decent to high quality gun. Once you have the gun dialed in, this product works great and fills in nicely after the second pass. A third pass and most light imperfections are gone.
Date published: 2013-12-14
Rated 5 out of 5 by from great stuff!!! The guys at Eastwood know me and they also know I use PPG products in the shop. However, I decided to give the Eastwood refinishing products a shot and I am really impressed with the way this prime sprays and more importantly how easily it sands. I'll definitely be using more of their refinishing products in the future.
Date published: 2010-07-16
Rated 5 out of 5 by from Great primer! I used this stuff on a bumper cover repair with great results.Just make sure you use a tip larger than a 1.4 if you are going to spray large panels without reducing it. Overall, i am very happy with it and will be ordering more for my other restoration projects.
Date published: 2011-05-26
Rated 4 out of 5 by from Decent product I had to reduce this product quite a bit. It almost dries to fast but that could have been my reducer. It fills great and sands very easy compared to other brands I've used. I would probably be using this primer again in the future.
Date published: 2014-04-22
Rated 5 out of 5 by from Great Primer! Sprayed smoothly from an inexpensive HVLP with no reducer necessary. Flowed out great. I sprayed this without a paint booth, but was fortunate enough to have ideal temperature when spraying. The results far exceeded my expectations.
Date published: 2014-05-15
Rated 5 out of 5 by from Good product Easy to use and sand .
Date published: 2011-07-19
Rated 5 out of 5 by from Great Product! Great Primer! I have just tried this primer for the first time. It sprays on real well and sands very nice. I should have used more reducer and then I would not have had to sand so much. However, this is a very good product and dried quickly with no runs, drips, or errors. Thanks Eastwood!
Date published: 2010-04-04
Rated 5 out of 5 by from A Favorite I sprayed this with the "Contour" gun with a 1.8 nozzle. I found I had to reduce it with one part reducer to get it to spray well. It fills minor imperfections beautifully and sands to a very smooth finish. The adhesion is excellent. Would definitely use it again.
Date published: 2013-12-05
  • 2015-05-04T08:59CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_15
  • loc_en_US, sid_50240ZP, PRD, sort_relevancy
  • clientName_eastwood

Can I use the 2k urethane primer for blocking over your epoxy primer?

Asked by: ME Williams
Yes, it's designed to be applied over paint, body filler, or self-etch or epoxy primer in 3-4 wet coats and then block sanded smooth.
Answered by: MikeL
Date published: 2015-03-14

I have been using some Martin Senior 2k urethane primer/surface, I think it was tp520. Because of the low voc requirements they do not have it available any longer. I am looking for a good primer/surface/sealer. How does this one compare?

Asked by: Rustyman
This product is directly comparable to any other automotive urethane surfacing primer.
Answered by: MikeL
Date published: 2015-03-14

how long after I spray the 2K urethane primer do I have before I have top coat it with B/C?. thank you Bob.

Asked by:
If you are following per the instructions and within the correct temperature range, after applying, within a few hours it'll set up, you can block it, and proceed with base coat anytime after
Answered by: SeanA
Date published: 2014-12-23

What do you use for cleaning the gun after spraying?

Asked by: cam90
Our Aerosol Injected Cleaner works well for cleaning paint guns. http://www.eastwood.com/aerosol-injected-cleaner-11-oz-net-49427.html We also offer Naked Gun cleaner. http://www.eastwood.com/naked-gun-low-voc-paint-gun-cleaner-gallon.html
Answered by: NickC
Date published: 2014-10-14

what reducer do you use with it

Asked by: raymond g
You would use a shop grade urethane reducer. http://www.eastwood.com/eastwood-s-slow-medium-fast-urethane-reducers-qts.html
Answered by: NickC
Date published: 2014-10-12

Will it hurt this primer to be out in the weather for a while before sanding and painting 

Asked by: Stingray
  • 2015-05-04T09:42CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_6
  • loc_en_US, sid_50240ZP, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Eastwood 2K Urethane Primer Surfacer Gray- Gallon 4:1

Item #50240ZP Brand: Eastwood

Provides quick, easy sanding; exceptional holdout and fast film build
Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations; check with your local and state guidelines as some areas may have stricter regulations than others.

Details

Apply this Gray 4:1 Urethane Primer over old paint, base metal or body filler Eastwood 4:1 Urethane Primer is perfect for overall jobs, patch panels and high-end restorations.
  • Fills well
  • Sands easily
  • Excellent color holdout for all top coats
  • 1-gallon can

More info...

About Eastwood 2K Urethane Primer Surfacer Gray- Gallon 4:1

EW Urethane primer is a two component gray surfacer designed for overall jobs. It fills well, sands easily and provides excellent color holdout for all top coats. Mixes 4:1 with 50241 ZP catalyst. May be applied over old paint, body filler & even bare metal. Ideal for block sanding in 3-4 hrs after application


Contents

1-gallon can of Gray 4:1 Urethane Primer


Accessories

50241 ZP Catalyst 12506 paint and Primer gun set 12817 paint Accessory kit 34186 paintucation DVDs 19875 Air Dryer 12454Z Block sanding kit 12712 ZP Rage body filler 12389Z Guide Coat


MSDS Sheet

Click Here for Material Safety Data Sheet


Product Information Sheet

Click here for product information sheet


Customers also viewed: