• Home
  • Eastwood 50lb Pressure Abrasive Blaster
Eastwood 50lb Pressure Abrasive Blaster is rated 3.9 out of 5 by 7.
Rated 4 out of 5 by from Just OK I bought this to blast a 1969 mustang. I have done most of the car and Iam fairly happy with the results. There are a few items that need to be addressed on the unit. After about 20 runs the tee at the bottom has eroded right where the hose attaches and it is blowing sand everywhere. Also where the nipple screws into the top of the tank is poorly designed because it needs to be braced so that it does not sag. I took off the trigger because after 5 minutes of holding that open your hand is going to start to cramp. I would also recommend that you get lots of shield replacement because after about 4 runs your are not going to be able to see your work very well. I also bought a cheap tent off of e-bay to keep all the media from going all over the place.
Date published: 2015-01-27
Rated 5 out of 5 by from works fine for the money Basically the unit performed as expected, had no issues with function or operation. It did an exellent job on the first project that I used it on and this reveiw is based on that, more use will be the real test but as of now I'm very happy with the way it performed.(ran 150ibs. of blast media through it this time.) It definately does use up the blast media fairly quickly and I had to reload it quite a bit but that is not a deal breaker. You can regulate how much output the unit has. I would definately recommend this product.
Date published: 2013-02-22
Rated 5 out of 5 by from Small machine with big machine features I bought this machine hoping I could spot blast rust and refinish equipment. I thought I would need more air and a bigger machine. After I put it together and went through the adjustments I found this thing can do a lot of work. It's well built and my compressor keeps up with it. I couldn't be happier. It does require common sense and some mechanical ability to operate. I have read some reviews where it was clear the people not the product were to blame for poor results. The best advice I can give is keep the tank full. As the media draws down it can interrupt flow.
Date published: 2016-08-16
  • y_2017, m_8, d_14, h_6
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_51117, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

What am I doing wrong. Pressure blaster works for 30 sec then clogs up. using 60 grit Black Beauty media. Any Ideas

Asked by: OldflyerII
Two things to check. Most importantly check grit size of media. This unit needs the grit size to be 80 grit or finer, Black Beauty is generally much more coarse. Second check manifold on bottom of unit, it should not be wide open.
Answered by: S Church
Date published: 2017-06-28

Can this unit be run with a pull behind compressor with higher cfm?

Asked by: Elroy
You can always have a higher CFM compressor when running any air tool.
Answered by: S Church
Date published: 2016-11-10

The "T" fitting on the bottom of this blaster has worn through.  I could not find a replacement listed anywhere on this web site.  Is this fitting available?

Asked by: Keppy
Feel free to contact our customer service department at 1800-345-1178 or orderhelp@eastwood.com to get replacement parts.
Answered by: S Church
Date published: 2016-10-17

Can you use this for walnut shells?

Asked by: jwilliams198
unfortunately walnut shell is to large to use in this unit.. This machine works with 8- grit or finer media..
Answered by: KHoffnagle
Date published: 2017-03-31

Can crushed glass be used in this blaster

Asked by: Edd1
Crushed glass would be to abrasive for the unit. I would recommend an aluminum oxide or glass bead 60 grit or finer. The 60 grit media will work better in the unit then the crushed glass.
Answered by: Ed O 88
Date published: 2016-08-30

Can sand be used as media in this blaster? If so what size?

Asked by: Gaboy
Sand of any kind should not be used. Not only is it a severe health hazard, the material is far too abrasive and will harm the internals of the blaster.
Answered by: MikeL
Date published: 2016-08-30

Can this be retro fitted for soda blasting?

Asked by: bombz
Yes our retrofit kit will work on any of the blaster units
Answered by: SeanA
Date published: 2016-08-30
  • y_2017, m_8, d_13, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_en_US, sid_51117, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood 50lb Pressure Abrasive Blaster

Item #51117 Brand: Eastwood

50-lb. blaster has large, high-flow valves to speed rust/paint removal

Out of stock

Only $119.99

 

Details

50-lb. "High-Flow" Pressure Blaster helps you remove rust and paint faster.

  • 50-lb. media capacity
  • Large 1/2"-I.D. blaster hose and fittings
  • 8'-long, heavy-wall blast hose with dead-man valve
  • Requires just 10 cfm at 90 psi
  • All-steel welded top-loading hopper and pressure gauge

Eastwood's "High-Flow" Pressure Blaster features high-volume, extra-large valves, which means more air volume and more abrasive flow for faster removal of rust and paint.


More info...

About Eastwood 50lb Pressure Abrasive Blaster

Sturdy welded hopper, 1/2" heavy-duty nozzle, heavy-wall blast hose and safety pressure-relief valve make this one rugged, durable, and very efficient abrasive blaster. Don't skimp with one of those low-cost units that frustrate you with clogging and sporadic media spraying. This Eastwood pressure blaster completely strips the average frame in less than a day, rather than weeks using other units or methods. Designed for high flow with minimal air input; a compressor producing a minimum of 10 cfm at 90 psi will work fine. 10"W x 14"L x 33"H.

Rolls easily to your job site. For best results and the most efficient operation, use clean, dry, 80-grit or finer abrasive media. 1-year limited warranty.


Contents

50-lb.-capacity Blaster (15-30 minutes of blasting)
Blast Hood
Moisture Separator
1/2"-ID x 8'-long Hose
4 Ceramic Nozzles (2.0, 2.5, 3.0 and 5mm)


Instructions

Click here for instuctions


70/100 Glass Bead 100/170 Glass Bead 10/40 Ground Glass 40/70 Ground Glass 60 Grit Silicone Carbide 60 Grit Aluminum Oxide 90 Grit Aluminum Oxide 12/20 Walnut Shells


Safety

WARNING: Blasting emits abrasive under pressure. Adequate respiratory, eye, and body protection must be worn during use. Inhalation of silica-based media particles have been known to cause cancer and other deadly diseases, and must be avoided. Wear NIOSH- approved respiratory protection while operating this equipment.


Customer Reviews

Questions & Answers

Customers also viewed: