- Eastwood Anti-Heat Compound 1 Qt
Eastwood Anti-Heat Compound 1 Qt is rated out of 5 by 2.
Rated 5 out of 5 by 67VW Rust Bucket from This stuff works great The putty was a little difficult to apply at first. It was crumbling pretty bad until I figured out it needed to be re-hydrated. After adding some water to re-hydrate it, it was much more cohesive and adhesive to the car. I had to fill a hole about the size of a nickel on a large flat area of the fender and there was no warping whatsoever.
Date published: 2013-07-05
Rated 4 out of 5 by Lucky from The right tool for the job Eastwood Anti Heat Compound is an asset to the average hobbyist, as well as the professional fabricator and restorationist. Having been involved with customizing and restoring cars and motorcycles since age 11, I have tried a veritable plethora of products in my time (I'm 50 now, by the way) This is not the first time I 've used this product, just the first time I've had to replace it. The first time I bought/ used it was about 20 years ago. This product is indespensible as a jigging putty to hold small parts in place, is absolutely essential to aid in avoiding warping/ pulling of metals when seaming and welding long beads in sheet metal work, and is possibly the only way to minimize warping/ pulling when performing sheet metal fabrication in stainless steel fabrication and repair. I currently work in a food production facility, and perform all of my work in stainless, and 90% of my welding is TIG, and as anybody who has TIG welded thinner stainless sheet metal will tell you, warping and shrinkage is the bane of your existence. One of the added benefits of this product, is when it is packed across the backside of where your weld bead will run, is that the "sugaring" (oxidization) of the backside of the weld is almost completely eliminated, thus minimizing the need for back shielding the weld with a seperate rig for a shielding gas. When having to weld a stud or a brace in place in the middle of a large exanse of sheet metal, using a generous amount of the putty on the backside of the welded area, as a heat sink, will almost eliminate the pulling and shrinkage normally associated with performing these tasks. If you are a serious hobbyist, a casual shadetree repair guy, or a hardcore build it yourself fabricator like me, this product is a 'must have' in your arsenal of fab/ welding tools, and I have and would reccommend its use to anyone who does any kind of welding. Now- go out there and build some stuff, will 'ya? Lucky
Date published: 2012-04-04
Is it reusable
This product is reusable and water can be added to wet it. Below are the instructions from the jar. Anti-Heat absorbing compound shapes like putty and will not burn, crack, melt, swell, or interrupt alignment. Use when welding, to hold irregular parts firmly in place. Anti-Heat may be used as a heat dam to prevent heat from traveling to areas that may be damaged by heat, such as enameled sections, rubber, glass, paint, and will help minimize distortion when welding on sheet metal. DIRECTIONS: Using a thin layer of Anti-Heat, cover entire area to be protected. In case of extreme heat, use thicker covering. When used for positioning, treat each part individually. Place one part on a mound of Anti-Heat as the other part is placed on a separate mound of Anti-Heat. Position parts as desired. May be reconstituted with water for reuse. Made in U.S.A. WARNING: Protect yourself and others. Read and understand the label. Welding generates FUMES and GASES that can be dangerous to your health, ARC RAYS that can injure eyes and burn skin, and, in some cases, ELECTRIC SHOCK that can kill. • Read and understand the manufacturer’s instructions regarding your welding equipment and employ standard safety practices. • Avoid inhaling fumes. Use enough ventilation, exhaust at the arc, or both, to keep fumes and gases away from your breathing zone and the general area. • Wear correct eye, ear, and body protection. • Wash hands after handling this product.
Date published: 2015-03-16
Eastwood Anti-Heat Compound 1 Qt
Item #31042 Brand: Eastwood
Withstands temperatures to 3,000 degrees to help prevent heat damage
Withstands temperatures to 3,000 deg F.More info...
About Eastwood Anti-Heat Compound 1 Qt
Withstands temperatures to 3,000 deg F.
Customers also viewed:
Ten 1/4-lb. sticks (30% tin, 70% lead) for long-lasting body repairsOnly $39.99
Holders grip sheet metal parts before final welding...hands-freeOnly $39.99
Easily align and grip panels for precise butt welds