• Home
  • Eastwood Concours Paint Gun w/3 tips Plastic&Metal Cup

Eastwood Concours Paint Gun w/3 tips Plastic&Metal Cup

Item #51605 Brand: Eastwood

Requires only 4cfm @29psi!


The Eastwood Concours Paint Gun helps you spray-on a beautiful "collector-car" finish...yet it's powered by your home compressor with only 4 cfm @ 29 psi!

  • Includes 3 stainless steel needle/nozzle/air caps (1.2, 1.4 and 1.8mm)
  • Anodized adjustment knobs and air cap ring
  • Lightweight, satin-finished aluminum body
  • Compatible with most home-shop compressors
  • Backed by Eastwood's 10-year limited warranty

There's no need to buy an expensive professional paint gun when Eastwood's full-size Concours HVLP spray gun has the same "high-end" features, but at 20% of the cost! And your home compressor provides all the air power you need (4 cfm @ 29 psi) to work with this Concours paint gun.

More info...

About Eastwood Concours Paint Gun w/3 tips Plastic&Metal Cup

This automotive paint kit includes the Eastwood Concours HVLP gravity-feed paint gun, which is an aluminum-bodied gun built for working comfort, reliability and years of service. With a working pressure of 29 psi and requiring only 4 cfm, this gun is ideal for the professional or hobbyist. The needle/nozzle and passages are stainless steel, making it compatible with both solvent and waterborne coatings. Includes tool kit and 1/4" NPT connection.


51550 Eastwood HVLP Gun with 1.2mm Cap/Needle/Nozzle for basecoats
51552 1.4mm Cap/Needle/Nozzle for clear coats
51553 1.8mm Cap/Needle/Nozzle for primers
51550B Teflon-Coated Aluminum Cup, 600cc
51550A Plastic Cup, 600cc
51136 Eastwood Paint Chip Chart


29953 34-oz. DeKups® Disposable-Cup Starter Kit
51559 Digital Regulator
50207 DeKups Adapter
20474 4-Stage Air Dryer System
51537 Complete Garage Air Line System
10194ZP PRE Painting Prep 30 oz.
51561Z Liquid Ice Buffing System


Download instructions in PDF format

Eastwood Concours Paint Gun


  • 4 CFM @ 29 PSI max. working pressure at the air inlet, 10 PSI max. at the Air Cap
  • M16 x 1.5NPS cup attachment threads
  • 1⁄4" NPT Air Inlet threads

  1. A 5/16" I.D. minimum air hose at a 25' maximum length is recommended for best results. A smaller I.D. hose and greater length may produce unsatisfactory results.
  2. Review complete instructions and become familiar with the "feel" of the gun.
  3. Clean out cup and gun with solvent to remove any residual manufacturing impurities and dry thoroughly.


Please note that many variables affect the adjustment of a paint gun such as paint viscosity and type, atmospheric conditions and operator preference. The following are some guidelines to get started but some time spent acquiring the "feel" of the gun and test spraying on sheets of masking paper are recommended before applying paint to your car. Always "tune" the gun before each use as conditions may not be the same as the previous use.

1. The "Fan" control knob (smaller blue knob at the top rear of gun) is opened by turning in a counter-clockwise direction. This controls the size of the spray pattern or "fan" and the droplet size. Out with the knob = larger pattern/larger droplet size, in = smaller pattern/smaller droplet size.
2. The "Fluid Needle" control knob (larger blue knob, below the fan control) is opened by turning in a counter-clockwise direction. This controls the amount of paint flow to the nozzle. Out with the knob = more paint,less atomization, in = less paint.
3. The "Air Valve" control knob (small blue knob at the bottom of the gun near the air inlet) is opened by turning in a counter-clockwise direction. This is a "fine tuning" for air flow in the gun. You generally want to start out fully open and decrease air as needed.
4. With practice you will quickly acquire a "feel" for the gun and will be producing professional results.

Maintenance and Cleaning


It is extremely important that the gun be disassembled and cleaned after every use!

1. Pour out then wipe out any remaining paint in the cup, fill the cup with water (for water borne paints) or solvent (for solvent based paints) and spray in a safe area until the spray is clear.
2. Remove the Cup.
3. Remove the Fluid Control Knob (lower blue knob at the rear of gun) fully by turning in a counter-clockwise direction.
4. Remove the spring with the fluid knob and pull the needle out from the rear of the gun.
5. Remove the Air Cap.
6. Remove the Nozzle by unthreading with the #13 hex in the included wrench.
7. Inspect the internal passages of the gun for any remaining traces of paint and using the included brush and water (for water borne paints) or solvent (for solvent based paints), clean out the passages and rinse.
8. Blow out any remaining water or solvent and reassemble the gun in the following order:
9. Thread the Nozzle into its bore and snug in place with the #13 hex of the included wrench.
10. Slide the needle back into place.
11. Slide the spring over the end of needle and thread the knob on.
12. Lastly, thread the Air Cap onto the end of the gun keeping the air horns in the horizontal plane.

Optional Accessories

1.2 Cap, Stainless Needle & Nozzle Set
1.4 Cap, Stainless Needle & Nozzle Set
1.8 Cap, Stainless Needle & Nozzle Set.
DeVillbiss DeKups Adapter
M16 x 1.5NPS 3M PPS Adapter
600cc Aluminum Cup for solvent based paints


Always wear eye, skin and respiratory protection. Follow tech data sheet and MSDS of the paint you are applying. Always follow paint manufacturer's safety information. Always paint in a well-ventilated area, away from open flame and sparks.

Customers also viewed: