• Home
  • EW Contour Polyester Primer Surfacer Qt

EW Contour Polyester Primer Surfacer Qt

Item #13522ZP

Sprayable high-build filler is an
excellent base for any paint system
Eastwood's Sprayable Polyester Primer-Surfacer is a 2-component high build sprayable body filler that serves as an excellent base for any paint system. It has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE Finishes, self Etching Primers and body fillers. Its high solids and high build formula allows you to achieve a laser straight surface prior to painting. Includes catalyst.

Details

Contour™ Sprayable High-Build Primer/Surfacer serves as an excellent base for any paint system

  • High-Build With Excellent Filling Capabilities
  • Easy To Sand With No Shrinkage
  • Excellent Adhesion To Metals, Fiberglass, and Body Fillers
  • Includes hardener

2-component polyester primer/surfacer has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE finishes, self-etching primers and body fillers.


More info...

About EW Contour Polyester Primer Surfacer Qt

Eastwood’s Sprayable Polyester Primer-Surfacer is a 2-component high build sprayable body filler that serves as an excellent base for any paint system. It has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE Finishes, self Etching Primers and body fillers. Its high solids and high build formula allows you to achieve a laser straight surface prior to painting. Includes catalyst.


Contents

Primer: 32 Fl Ounces/ 946mL Catalyst: 2 oz/ 60g


Application


SURFACE PREPARATION:

1. Surface must be clean and free of wax, grease and debris. Use Eastwood’s PRE Painting Prep to remove all contaminants.

2. Sand/abrade surface
  A. Body Filler & Putty: Rough sand with 80 grit, then 180-220 and featheredge with 320 grit
  B. Untreated Steel, Galvanized and Aluminum: Sand with 80-180 grit
  C. Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish with 320 grit.

3. Completely final sand surface with 320-400 grit paper and re-clean with PRE Painting Prep MIX: 5% by weight

SPRAY GUN & APPLICATION RECOMMENDATIONS:

1.8mm to 2.5mm Fluid Tip Size, 35 to 40 PSI

Apply two or three medium wet coats as needed. Heavy wet coats should NOT be applied.
Dry spray may be removed be for recoating. Allow 90 minutes dry time before sanding at 68°F (20°C). Finish with 220 grit followed by 320-400 grit

DRY TIMES AT 68°F (20°C)

Flash: 5-10 minutes
To Sand: 90 minutes, over self etching primer: 4-6 hours
To Topcoat: 90 minutes, over self-etching primer: 4-6 hours
Force Dry: Purge 10 minutes, Bake: 30 minutes at 140°F (60°C)
Pot Life: 30 minutes at 68°F (20°C). If needed add 5-10% acetone to extend pot life.
Clean equipment with lacquer thinner immediately after use. This product is not meant for use below 60°F (16°C), dry time and performance will be dramatically affected.

CAUTION: DO NOT return catalyzed material back into can. To avoid contamination, seal lid tightly after each use. Store in a cool dry place.


Safety

Always wear eye, skin and resp[oratory protection when using this product always apply in a well ventilated area. consult MSDS and product label for specific safety warnings


Warranty

Made in Canada to Eastwood's strict specifications and quality standards


Application

Surface must be clean and free of wax, grease and debris. Body Filler & Putty: Rough sand w/80 grit, then 180-220, featheredge w/320 Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish w/320 Gun requirements: 1.8mm to 2.5mm Fluid Tip Size, 35 to 45 PSI Apply 2-3 medium wet coats. 90 min dry time @ 68°F finish with 220 and final with 320-400 grit.


Customers also viewed: