• Home
  • Extreme Chassis Black® High Gloss 14 oz. Aero
Extreme Chassis Black® High Gloss 14 oz. Aero is rated 3.9725 out of 5 by 109.
Rated 5 out of 5 by from Extreme Chassis Black Gloss - Excellent Purchased the Extreme Chassis Black Gloss to paint a few suspensin parts on my frame-off project. Probably the most expensive spray paint you will ever buy, but is far superior to any other I have used in the past. Lays down nice and coverage is excellent. If you only have a few parts to paint and don't want to break out the spray gun, this is the paint to get. The shine is great. Looks just like some powder coated pieces I have on my chassis. Seems to be very durable so far as nothing got chipped or scratched during assembly. Just be sure to use the Eastwood Chassis Black Primer first for best adhesion and durability. Over all an excellent product, just a little on the expensive side.
Date published: 2012-06-23
Rated 5 out of 5 by from Extreme Chassis Gloss Black is great! I recently rebuilt the 12-Bolt rear end in my 99 Camaro and wanted to finish it with a coating that is durable and looks good. After a lot of research I brushed on POR-15 but was a little dissapointed with the end result. They say it is "self leveling" but I could still see where I had overlapped layers while going around the tubes and there were inconsistencies in the color. I smoothed out the POR-15 and bought two spray cans of the Extreme Chassis Black-High Gloss. Damn this stuff works great!!! Not only is it durable, but it looks like it was sprayed from a real spray gun and cleared after. I definitely recommend using this stuff on any chassis parts if you want a great appearance and don't mind spending the extra $$$ for a better quality paint than what you can get at the hardware store.
Date published: 2010-12-08
Rated 5 out of 5 by from Extreme The only downside if there is one is that it isn't cheap but then if it was cheap I don't think it would be the product it is. One can does cover quite a bit because it is not watered and thinned out like a lot of spray can paints are. It sprays good, lays down good, is very durable and holds its gloss very well. It is also a black black without much of any other tint like you see in some black paints. It can be used for a lot more than just spraying frame rails and suspension parts.
Date published: 2011-01-06
Rated 5 out of 5 by from Another use for a great product Two years ago I had the outdrives on my boat professionally repainted with a black epoxy paint. It cost $850. After one summer in the water, the paint had totally lifted off the outdrives--leaving only the primer. Rather than spend another $850, I cleaned them good with PRE Paint prep and tried repainting them with two coats of Extreme Chassis Balck Gloss. This fall when I pulled the boat the outdrives were intact. Just another use for a great product and it cost me less than $50!
Date published: 2009-10-15
Rated 5 out of 5 by from Chassis Restoration - 41'Studebaker Champion After using different chassis paints over the years together with a wide variety of rust primers, I decided to utilize Extreme Chassis Black as my top coat and was not disappointed with the results. Prep my frame from bare metal to application of a brand name metal rust primer. Then sprayed Extreme Chassis Black with outstanding results. Great product coverage, two coats is a must to ensure proper coverage. I will use this product again, Thanks !!!
Date published: 2014-10-26
Rated 5 out of 5 by from Love it! Metal was prepared by sandblasting so it was perfectly clean. Used the Extreme Chassis Black primer and waited the recommended 24 hours prior to top coating with the gloss. After 48 hours, the paint is hard as nails and look fantastic. I'm very impressed with this product. Like any paint work, the end results are dependent on the prep work so I don't know what would happen if you don't follow the directions, if you do, it will look great.
Date published: 2012-08-05
Rated 4 out of 5 by from works as said my hitch on my 98 ranger took a beating this winter so i purchase the rust encapsulator and the extreme chassis black once i clean the loss rust and wipe any oil and dirt away i sprayed the encapsulator and let it dry for 8 hrs and top coated the hitch with the extreme chassis black when real nice better than i though it would and even thow its only been a week snice it still looks wet
Date published: 2011-04-17
Rated 5 out of 5 by from Extreme Gloos and Satin Outstanding product. I am rebuilding the engine compartment of a 1970 chevelle and am using the high gloss on the upper and lower control arms. It goes on very easy and looks great. Looks alot better that I thought. I also used the Extreme satin on the frame and I am very happy with that. Even after putting on the new parts the paint holds up. Both are great products.
Date published: 2010-01-27
  • 2015-07-31T11:09CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.5
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_109
  • loc_en_US, sid_11172Z, PRD, sort_relevancy
  • clientName_eastwood

Will ECB adhere to plastic and or fiberglass if prepped properly?

Asked by: DMC12
You would need to apply a plastic adhesion promoter before applying the paint but yes it will
Answered by: SeanA
Date published: 2015-07-14

how many spray cans for a 1950's 1/2 ton truck frame?

Asked by: Schills
The spray cans cover approximately 8 sq ft. You would have to estimate how many square feet your truck frame is to figure out how many you will need. It would be impossible to me to tell how many you need without knowing the frame size.
Answered by: S Church
Date published: 2015-07-10

What tip size should i use to spray this material?

Asked by: housston
A spray gun with a 1.4 tip would be perfect for spraying this material.
Answered by: S Church
Date published: 2015-07-09

does chasis black have uv protection?

Asked by: fred4077
Yes, chassis black is UV resistant
Answered by: SeanA
Date published: 2015-06-18


Asked by: JUNKMAN
After blasting your truck frame you will want to clean it with a wax and grease remover like our "Pre" and then put down an Epoxy primer prior to the Chassis Black.
Answered by: S Church
Date published: 2015-07-03

How do you apply this chassis paint and if you spray it do you have to thin it and with what?

Asked by: Bobarino
You would want to spray the product using a 1.4 tip and no it doesn't need to be thinned
Answered by: SeanA
Date published: 2015-05-21

Can I apply the Extreme Chassis Black Satin over an Etching primer, like the Duplicator etching primer?  If not, then what can I put between the etching primer and the extreme chassis black satin.

Asked by: JIR L
No, on the product description it clearly indicates it cannot be used with a self etch primer
Answered by: SeanA
Date published: 2015-05-21

hi I will be painting a new bare metal Jeep frame. what primer would I use under this extreme chassis black gloss

Asked by: wilefish
You would use either extreme chassis black primer OR epoxy primer
Answered by: SeanA
Date published: 2015-04-20
  • 2015-07-31T11:27CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.5
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_18
  • loc_en_US, sid_11172Z, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Extreme Chassis Black® High Gloss 14 oz. Aero

Item #11172Z

3X more resins make it 3X more durable than original Chassis Black


Extreme Chassis Black Gloss has 3X the resins of traditional coatings, so it's tough enough for any undercar component You spend hours prepping your frame and suspension parts; now top-coat them with a tough, OEM-matching, glossy formula that provides extreme durability! 3 times more resins make it 3 times more durable than our original Chassis Black.
  • Improved resistance against corrosion, chips and scratches
  • Resists brake fluid, fuel and solvents
  • Matches OEM finish
  • Apply multiple coats without lifting

More info...

About Extreme Chassis Black® High Gloss 14 oz. Aero

You spent many hours prepping your frame; now paint it with the best Chassis Black formulation available. Up to 3X more durable than Original Chassis Black. This maximum durability formulation offers improved brake fluid, fuel, solvent, chip and scratch resistance. For improved adhesion prime clean bare metal with Extreme Chassis Black Primer aerosol (11193Z), qt. (11194ZP), or gal. (11195ZP). Prime rusty metal with Eastwood Rust Encapsulator. Allow 15-20 minutes between coats of Extreme Chassis Black. Can be recoated at any time without lifting.


Click Here for Material Safety Data Sheet

Customers also viewed: