• Home
  • Flanger/Punch Tool Pneumatic 7/32"
Flanger/Punch Tool Pneumatic 7/32" is rated 5.0 out of 5 by 2.
Rated 5 out of 5 by from good I have only tried this on a peice of scrap sheetmetal that I cut from a door skin.It worked well to punch holes and make flanges on the metal.It was metal from a 1946 truck whitch is heavier than on todays cars.I would buy again If I needed it.
Date published: 2013-05-08
Rated 5 out of 5 by from above average Have used it already. Very pleased with results.
Date published: 2014-05-06
  • 2015-02-25T12:22CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_31015, PRD, sort_relevancy
  • clientName_eastwood

Maybe a dumb question, what is a flanger and will it punch holes in a 1960's British car sheet metal?

Asked by: 4Mee
A flanger puts an offset flange in the metal, so that you can lap weld a replacement panel with the repair panel sitting flush. It will flange panels up to 20 gauge and will punch holes in panels up to 14 gauge.
Answered by: NickC
Date published: 2014-10-17

Hello,      What gage metal is .040 ? Will this tool flange and punch 16 gage panels?      Thank you

Asked by: BillStep
.040 is between 19 and 20 gauge metal. This tool will flange metal up to 20 gauge and will punch metal up to 14 gauge.
Answered by: NickC
Date published: 2014-09-24

Does this tool require oil lubrication ? If so, how does one accomplish this ?

Asked by: Carguy
This tool does require oil lubrication. A few drops in the air inlet at each use will ensure the tool is lubricated.
Answered by: NickC
Date published: 2014-09-22

does it step up or down facing the material? can it be changed as to how the step is ?

Asked by: glenner
  • 2015-02-25T12:46CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_US, sid_31015, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Flanger/Punch Tool Pneumatic 7/32"

Item #31015 Brand: Eastwood

Produces 0.040" offset flanges and
punches 7/32"-dia. holes

Details

It's a Flanger, and a 7/32" Punch, in one handy pneumatic tool Double-action head swivels to let you create flanges and holes from any angle with just a squeeze of the handle.
  • Produce 0.040" offset flanges
  • Punch 7/32"-dia. holes
  • Requires 4 cfm at 90 psi

More info...

About Flanger/Punch Tool Pneumatic 7/32"

2-in-1 pneumatic tool saves space in your metalworking toolbox! One side of the double-action head produces 0.040" offset flanges on 20-gauge metal or thinner for clean welding with little grinding. The other side produces perfectly clean 7/32"-diameter holes that are ideal for plug welding; punches holes 1/4" from the panel edge in up to 14-gauge. Unique swivel-head design lets you work from almost any angle.


Application

The Pneumatic Flange and Punch Tool produces a 0.040" offset flange for flush repairs up to 20-gauge, or punches clean 7/32" holes in up to 14-gauge steel. Requires 4 cfm at 90 psi. NOTE: The center of the hole produced is 1/4" from the panel edge.


Accessories

20560 Straight Pneumatic Flanger-Punch Tool for 5/16" (8mm) holes


Customers also viewed: