Cart is Empty

View

Related Products

Check items to add to the cart or select all

Eastwood Digital Torque Wrenches and Adaptors

Eastwood Pneumatic Tools - Impact Wrench, Metal Sheers, Metal Saw

Recently Viewed Items

Gal. Auto Air Sealer White
Item #34330 004
FM Urethane Primer Activator 8 oz
Item #EPAP Z
Flap disc 4.5" Zirconia 60 grit
Item #11947

Community Poll

ABOUT SSL CERTIFICATES

Home /
Gator Guard II Truck Bed Liner Kit

Gator Guard II Truck Bed Liner Kit

Enlarge product image

Gator Guard II Truck Bed Liner Kit

Item #10129 Z

In Stock - Ready to Ship Today

Only $59.99

Buy 2 or more for $54.99 each and save 9%

Gator Guard II Liner Kit in black seals and protects your truck bed

A truck bed that's lined with a tough, durable, black coating like Gator Guard II increases your truck's resale value, reduces maintenance, and adds a nicely detailed look.

2-part epoxy formula
Black
Just spray, brush or roll on
1 kit covers 32 sq. ft.

This item cannot be shipped to Sacramento County

4 Review(s) | Add Your Review

Add Items to Cart Qty:

About Gator Guard II Truck Bed Liner Kit

If you'd use a standard drop-in liner, it can warp and trap water and contaminants that can lead to bed corrosion. But our 2-part epoxy system offers a non-skid, chip-resistant black finish that's flexible at low temperatures, so water and contaminants can't get trapped underneath. Easy to apply with a wide brush or roller, or spray-on with our 20441 Undercoating Gun. Adheres to firmly adhering paint or bare metal. Degrease area to be coated and mask. One kit covers 32 square feet, and most truck beds will require 2 kits (2 or more kits are available at a discounted price).

Each Truck Bed Liner Kit includes one container each of parts "A" and "B", a total of about 1.8 quarts (enough to cover the bed of a small truck). For larger trucks or heavier coats, get 2 kits at a discounted price.

Click Here for Material Safety Data Sheet

(Q) How long after application must I wait to use the truck bed?
(A) At 72 degreesF surface will remain tacky for 7 hours. After 48 hours, surface will have no product transfer and may be used for heavy loads. Do not wash surface with soap, water or any other solvents for a minimum of 2 days after application.

This coating is appropriate for all surfaces except polyethylene and similar plastics. Before coating, lightly scuff bed surface to roughen. Make sure surface is free of any grease or oil. Mix equal parts of "A" and "B" thoroughly. Brush or roll mixed material at a 5-10-mil thickness. For spray application using a Shutz-type gun, apply a medium-wet coat at 35-65 psi. Immediately clean off any overspray and applicator with mineral spirits or paint thinner. Works best between 65 and 95 degreesF. One kit coats 32 sq. ft. with a 5-10-mil coat.

Customer Reviews

(Posted on 11/13/11) good product
Review by jim

Quality
Price
Value

I used 2 cans on my super crew shortbed, minus the tailgate. looks good up until the sprayer (sold here) kept clogging, I would then put my finger on the nozzele and pressurize the can. This caused a couple big seagull turds to shoot out and land in the bed. So then I would remove the sludge can and stick the sprayer in some asetone and try again until it clogged. No idea what was happening, product was mixed well. sprayer sucked.

(Posted on 8/14/10) Very good
Review by David

Value
Quality
Price

So far am very pleased with durability and looks. I applied it to the floor of my '52 Willys Wagon. I don't know if I didn't apply it thick enough because one kit did the whole back floor.

(Posted on 7/27/10) Disapointed with appearance
Review by finkstr

Value
Quality
Price

I purchased the Gator Guard to use on my pickup toolbox rather than have it coated with Rhino Lining like the rest of the bed. Unfortunately that turned out to be a mistake. The surface turned out to be very rough with some areas even "sharp" to the touch. At first I thought that I had applied it incorrectly but that was not the case. I mixed and applied it according to the directions. Although the price iand value are fair, I cannot recommend this product.

(Posted on 4/19/10) great stuff, but needed more
Review by bovinedeity

Price
Value
Quality

First off, the suggested two kits for larger trucks doesn't really work. I bought two kits for my full-size longbed, I was able to get two thirds done and ran out. I going to try to finish with just one more, but its going to be close. I sprayed to the economy sprayer sold here.. Worked great at 75psi. Everything cleans up well with acetone. The A part of this epoxy is a thick sludge. Tis makes mixing an interesting and potentialy messy affair. Be prepared for that. Other than that, 2/3rds of my truck bed look beautiful.