- Eastwood Tunnel Ram 4:1 Basecoat Gallon
Eastwood Tunnel Ram 4:1 Basecoat Gallon
Eastwood Tunnel Ram Gray Metallic Basecoat Paint adds the superior durability of urethane to the ease of conventional basecoats.
- Apply a durable urethane finish wherever you live in the continental US, even CA
- Choose a fast, medium or slow Low-VOC Activator
- Makes 5 sprayable quarts
- Clearcoat is required on basecoat paints
- Mixes 4:1 with your activator choice
Basecoat Paint Kit is a low-VOC system, so it meets regulatory limits in highly-regulated areas, eliminating the need to switch to a waterborne system.
About Eastwood Tunnel Ram 4:1 Basecoat Gallon
BASECOAT PAINT MIXING RATIOS
Thoroughly mix four parts Low-VOC Urethane Basecoat with one part Low-VOC Urethane Activator. Use Fast (50308ZP) for small jobs, or temps below 75°F; Medium (50309ZP) for small jobs, or temps between 70-85°F; or Slow (50310ZP) for large jobs, or temps above 80°F. Keep in mind, other factors, such as humidity, air flow and total film thickness should also be considered. In many situations, it will be useful to add 10%-20% 50104ZP Zero-VOC Reducer to aid sprayabliity, flow and leveling. Remember, this is an activated basecoat system; only mix as much as is needed. Pot life is about 2 hours at 70°F.
PAINT GUN SET-UP
HVLP Gun: Fluid Tip 1.2-1.4 mm Inlet Spray Pressure 8-10 psi
Conventional Gravity: Fluid Tip 1.2-1.5 mm Inlet Spray Pressure 40-50 psi
Conventional Siphon: Fluid Tip: 1.3-1.6 mm Inlet Spray Pressure 40-50 psi
Apply Low-VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coats. Flash time should increase if additional coats are applied. Most colors will cover in two coats. A third and final coat may be applied to set even metallic pattern. If required, apply this light coat immediately after the previous full wet coat, moving the gun with faster passes, from further away. Mist basecoat onto the wet film until the metallic pattern is uniform.
Basecoat should dry dust-free within 10-20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45-90 minutes before taping on the fresh film. All dry times are approximate, at 70°. Temperature, air flow, total film thickness and other variable may extend these times.
One US Gallon of paint, 128 Fl. Oz One US Quart of activator, 32 Fl oz.
50104ZP Zero-VOC Urethane Paint Reducer
PRE Painting Surface Prep
Low-VOC Gray Urethane Primer
12569 Concours Master Gun Cleaning Kit
12846Z Aerosol-Injected Cleaner
SAS Bandit Respirator
Gen-Nex Painters Coveralls
15639 Concours LT HVLP Paint Gun 1.3mm
Always wear eye, skin and respiratory protection. Always paint in a well ventilated area. Consult MSDS and Tech Data sheets for proper safety precautions and usage. VOC= 3.5 lbs.gallon
Prep surface and remove all traces of contaminants. Use Eastwood's PRE Prep. Sand existing finish with 400-600 grit abrasive. Re-clean surface. Mix 4:1 with appropriate speed activator. Reduction not necessary. Shake Well. HVLP Gun Nozzle Size 1.2mm-1.4mm. Apply in 2 medium wet coats with 50% over lap. Allow 10 minutes flash time between each coat. Clear coat can be applied after 20-30 minutes. Maximum re-coat time is 18 hours. Otherwise surface must be abraded with 400-600 grit. Use 50307ZP Low VOC Clear & Activator. Pot life is about 2 hours at 70'F
Questions & Answers
Customers also viewed:
Low VOC Formula
Starting at: $32.99
Delivers the shine and miles-deep appearance of a show-quality finish
Starting at: $29.99
2-component gray surfacer designed for overall jobs
Starting at: $29.99
Maintains good color hold-out on steel, aluminum, fiberglass, body fillers
Starting at: $39.99
Eastwood 4:1 Premium Show Clear Kit 5 quarts 15351ZP$179.98