• Home
  • Eastwood Multi-Unit Welding Cart - MIG TIG Plasma
Eastwood Multi-Unit Welding Cart - MIG TIG Plasma is rated 4.3559 out of 5 by 59.
Rated 3 out of 5 by from Bottle rack is too narrow Overall the cart is "ok".... the bottom shelf is a bit too low, the lead hangers should be two per side instead of one.... but the biggest problem is you can only fit a very small gas bottle to the back of the cart. The top "U" shaped cradle is about 3/8" to narrow to fit a medium sized gas bottle. This effectively reduces this to a stationary "stand" instead of a "cart". My gas bottles have to be chained to the wall to use this so it's effective range is about 6-7 ft.
Date published: 2014-06-02
Rated 5 out of 5 by from Combo welding cart Purchased this item a couple weeks ago; and finally got a chance to assemble it last evening. Went together in about 20 minutes. Good looking piece of equipment. Using it for an Eastwood MIG 135 recently purchased as well. Finished assembling the MIG unit today as well. Did not get to "test-drive" the welder as of yet until I can pick up a tank of gas. Very pleased with the purchases. Also bought the cover, welding helmet, and helmet bag. Gladly recommend to others.
Date published: 2015-04-26
Rated 5 out of 5 by from far better than expected This cart was sturdier than expeeded. As someone else said, "far better than harbor freight". And you will need washers to make it really nice. Bolts are long enough to put washers on both the nut side and lock washer side. I did have one bolt strip out. However it really didn't strip. The nut was the wrong size. I think some sae nuts got mixed in with the metric nuts. I found the right size nut and it tightened perfectly. I recommend this cart for the price.
Date published: 2013-02-04
Rated 3 out of 5 by from Fairly good cart but could use improvement A definite step up from the harbor freight design. But Eastwood should have gone the extra 5% in design & they would have knocked it out of the park! Cart arrived with chipped finish & plastic trim on plasma access hole was shattered. I won't use the lower shelf because my Lincoln plasma will not fit & if I want the plasma so low to the ground I will put in on the ground. The holes for rod storage only work with 36" rod which I don't find convenient for tig welding.
Date published: 2012-01-26
Rated 2 out of 5 by from i coulda built my own better and cheaper cart is ok, easy to assemble and looks nice but its so flimsy. i got the front wheel stuck on a piece of slag and when i pulled (not hard) i almost bent the thing in half. coulda used some gussets or something. im disappointed. for $80 i expected alot more then i got. i have a hard time having a new welder on top of it, for fear it will fall of when the whole things twisting. i honestly coulda built twice the cart for half the money.
Date published: 2013-03-01
Rated 5 out of 5 by from A Great Welding Cart I purchased this cart for my MIG welder after looking at several sites and found it to be the style I wanted and it was sold by Eastwood It is very well made and was easy to put together. The instructions were clear and it only took me 30 minutes to put it together. Once together it held all of my equipment. It is sturdy and I would expect to get years of use. I can't find anything negative about it. It's a great welding cart.
Date published: 2014-11-15
Rated 4 out of 5 by from Not a bad cart Overall the cart is not bad. The included hardware is useless, the hardware might just as well have been made of plastic as 6 of the bolts stripped as soon as any torque was applied. The base should be a bit wider as with just my miller 211 on top I'm very concerned with it tipping over so I'm going to have to move the front wheels out further with some extra steel.
Date published: 2012-10-17
Rated 3 out of 5 by from Disappointed Less than impressed with this multi-unit welding cart, it dose have decent 3” and 7” wheels but the cart is made of stamped 16gage sheet metal, its flimsy and has no system to hold your welder on the top shelf other than some small bumps in the sides of the top shelf. I plan on reusing the wheels to build my own cart. Should have built my own cart to start with.
Date published: 2014-01-24
Rated 4 out of 5 by from Welding Cart I'm happy with the unit but it needs some sort of support for the bottom of the bottle so when the unit is moved it won't tip. It works well and supports all the welding machine/s and there clamps, hose, tools, helmet etc. It appears to be designed for the hobbyist, I'm not sure if it is sturdy enough for commercial use. It works for me and I recommend it.
Date published: 2014-11-23
Rated 4 out of 5 by from adequate Likr many others I bought this with the mig/plasma combo. Easy enough to assemble. Would be better if it had room for two gas tanks, one for pure argon and one for co2/argon mix. Had to put 90 elbow on plasma unit for the air hook-up because it was behind gas tank. All in all it does what it was designed to do. Would recommend as a buy.
Date published: 2013-11-18
Rated 5 out of 5 by from Eastwood weld cart is a good value From the time I opened the box until I set my welder up on the finished cart, my total time commitment was 55-minutes. This time included pulling all the packaging materials into the recycle bin and returning my tools to the tool box. In general, all went well. The assembly instructions are well written. I would have liked that the wheels were assembled last, this would have made for less movement during assembly. Two things that might be improved.. a break for using the welder on a slanted surface such as my driveway and a nest for the bottom side of the welding rod storage. Not a big deal, I will add my own. Only time will tell if the cart holds together after dragging it around my garage, driveway but all is good now.. I think I will add a nylon strap around the welder... Oh lastly, I think there was to much plastic in the packaging. I would have paid an extra buck to have everything paper based, envelopes, dividers.. maybe even metal bands.
Date published: 2014-01-20
Rated 5 out of 5 by from Very nice cart! Bought this cart to go with Eastwood's Plasma Cutter/Tig Welder package. I am glad I spent a little more money and bought this cart separately instead of buying the full Cart/Plasma Cutter/Tig Welder package that Eastwood also offers. I prefer to have the Tig welder on a flat surface rather than slanting backward as shown in the package images. It was incredibly easy to assemble, probably the best assembly instructions I have ever followed. The casters are nice size and roll very smoothly. I like the pull handle on the front and especially love the overall height of the cart. I bought a cheap cart somewhere else that's only 18" high or so for my welder at work and I absolutely hate it. I may end up buying another one of these! If I had to say something negative about it, I would say that the bracket on the back that holds the chain to secure the tank is a little flimsy. I may add a couple supports someday, however once I put a tank back there and chain it in maybe I won't even notice...
Date published: 2014-12-31
Rated 5 out of 5 by from cart assembly Assembly:as a joke I had a 9 year old neighbor put it together to See if he could he had no problems whatsoever with the assembly or instructions just goes to show you the ease of assembly good directions all the parts were there and it fits a 172 mig welder with bottle no problem thanks again
Date published: 2014-12-12
Rated 5 out of 5 by from Nice cart for the money. Nice cart, easy to assemble. Well built with a good finish. I put my Cut 40 plasma cutter on the bottom and my mig welder on the top. The only modification I made was to add two more hooks for hanging cables to the rear vertical support. This worked better for keeping the cables from dragging.
Date published: 2014-12-15
Rated 4 out of 5 by from Nice product for money spent Was easy to assemble,feels sturdy,rolls nice and smooth. Wheels have bearings in them. My Mig welder fit it perfect. Over all it s great addition to my shop. I am going to change the handle some to make it a little higher so I dont have to bend over when pulling it through the shop.
Date published: 2014-07-23
Rated 5 out of 5 by from Awesome cart This is a well built cart. Quality construction. Only 2 small issues. The welder slides around on top. Will end up getting some foam tape for feet. Also when using 55cf gas tank the chain only goes around valve not tank. Might add a lower chain. Otherwise the cart is great.
Date published: 2015-01-12
Rated 5 out of 5 by from Good for the money I bought this cart for my Eastwood Mig 250 on top and a plasma cutter on the bottom. Put a 141cf tank on it and it works well. It does need more and larger hose hangers. Over all it does what I needed it to do. Its a little pricey for the size but made well.
Date published: 2015-03-27
Rated 4 out of 5 by from Good Quality for the Price This cart holds my Hobart and my little Victor cutter quite well. It shipped soon and was packed well in the box, something you don't see enough anymore. It went together well and is sturdy enough for me after completion. Fit and finish are great as well.
Date published: 2015-01-13
Rated 5 out of 5 by from works great Bought this cart for the Eastwood tig 200 welder sits nice atop cart ,needed to strap down with a bungee due to the slick surface other than that it's great well built
Date published: 2015-04-27
Rated 5 out of 5 by from Excellent cart Cart was ordered with the tig/plasma cutter combo. Cart was well packaged, very easy to assemble accommodated both machines as designed, as well as a pile of accessories. Overall I am very pleased with this purchase.
Date published: 2012-08-12
Rated 4 out of 5 by from Nice! Well designed for the Eastwood products I ordered with it. Easy to assemble and is the perfect size for my garage area. I would definitely recommend one to anyone. In fact I did to a buddy and he bought one also!
Date published: 2012-09-24
Rated 4 out of 5 by from Very nice cart for the money. I backed down to four stars because it needs to have a way to anchor the top unit down. Its very easy to slide the top unit off of the cart. It is sturdy enough and it could use a couple more hangers.
Date published: 2014-01-06
Rated 5 out of 5 by from Just right I needed a welding cart after purchasing a eastwood mig 135. I was impressed with the overall quality and ease of assembly. Just what I needed for the welder, shielding gas cylinder and accessories.
Date published: 2015-01-15
Rated 4 out of 5 by from Nice cart I bought this along with the 135 and versa cut 40. Perfect fit! Very nice cart, heavy duty compared to most. Sturdy with everything on the cart. Good powder coat finish, GOOD product for the Price!
Date published: 2014-12-09
Rated 5 out of 5 by from welding cart great product went together in mere minutes, rolls fine bottle storage is good, really like the top shelf for the welder is level not slanted back, plenty of room between gas bottle and back of mig
Date published: 2015-01-19
Rated 5 out of 5 by from Excellent cart Cart was ordered wit the tig/plasma cutter special. Cart was well packaged,very easy to assemble, ans accommodates the two machines and a whole pile of accessories, I am very happy with the cart.
Date published: 2012-08-12
Rated 5 out of 5 by from Great welding cart The cart arrived in one box, packed great, very easy to assemble. The cart rolls very easy it has lot of storage on the two shelf below the welder. very happy with this welding cart
Date published: 2012-07-16
Rated 5 out of 5 by from Great cart Have a versa cut 60 and mig welder they both fit great and makes it great to have everything where you need it. It is plenty sturdy would recommend to anyone needing a welding cart.
Date published: 2014-10-02
Rated 5 out of 5 by from works well I have had the cart a couple of weeks. It was easy to put together and holds the MiG 175 and Versa Cut 60 with ease. The wheels are heavy duty compare to other units I look at.
Date published: 2014-11-05
Rated 5 out of 5 by from Great bang for the buck Always heard that inexpensive welding carts were not good. Not in this case. Went together very easily, Holds my welder and plasma cutter well, rolls easily, very sturdy.
Date published: 2012-10-29
  • 2015-05-03T10:45CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_2, bvpage2n
  • co_hasreviews, tv_0, tr_59
  • loc_en_US, sid_11616, PRD, sort_relevancy
  • clientName_eastwood

Eastwood Multi-Unit Welding Cart - MIG TIG Plasma

Item #11616 Brand: Eastwood

Put your welder on top, plasma cutter on the bottom, tools in the middle
Heavy Item - Special shipping charges may apply.

Details

  • Top shelf which will hold the MIG135, MIG175, or the TIG-200 welder
  • The bottom shelf will hold the Versa Cut Plasma Cutter
  • The middle shelf of the welding cart allows storage of necessary welding accessories
  • The Gas Bottle Mount incorporates a TIG Rod Holder to store up to 6 different tubes of filler rods
  • The design of the top shelf allows for the side access door on the MIG’s to be opened without taking the welder off the cart
  • Heavy duty front castor wheels
  • Molded Heavy Duty Rear Wheels
  • Satin Black Powder coated finish
  • Cut out in rear to allow plasma cutter cable routing through the rear of the cart
  • Holds up to an 80CF Gas Bottle
  • Front Mounted Handle for easy maneuverability around the shop
  • Two side hooks for cable storage

More info...

About Eastwood Multi-Unit Welding Cart - MIG TIG Plasma

These welding carts were designed by The Eastwood Company to make storage, accessibility and maneuverability of your welders and welding equipment easier than ever before.This cart incorporates a top shelf which will hold the MIG135, MIG175, or theTIG-200 welder. The bottom shelf will store your Versa Cut Plasma Cutter while the middle shelf allows storage of necessary welding accessories. The Gas Bottle Mount even incorporates a TIG Rod Holder to store up to 6 different tubes of filler rods. Assembles with simple hand tools.


Contents

Includes: Welding Cart with assembly Instructions


Application

Will hold the following combinations:MIG175 and Versa Cut Plasma CutterMIG135 and Versa Cut Plasma CutterTIG200 and Versa Cut Plasma Cutter.May possibly fit other brand units as well


Instructions

Click Here for instructions


Safety

This cart is intended to hold an 80 CF gas bottle, using a bottlelarger than this is not recommended.Always wear safety glasses and follow common practices when using hand tools.


Size

Welding Cart Dimensions

Total Height - 30.5"
Total Width - 16"
Total Length (not including Handle) - 32"
Total Length (including Handle) - 38"
Top Shelf Width - 11.75"
Middle Shelf Width - 11.75"
Bottom Shelf Width - 11.75"
Top Shelf Length - 20"
Middle Shelf Length - 15"
Bottom Shelf Length - 17.5"


Customers also viewed: