- Eastwood MIG Welder 175 Amp with Spool Gun
What is the orientation of the blades on the power cord? I need to ensure the cord will plug into the 220v outlet in my garage
Is this machine a 3 wire or 4 wire plug?
no gas tank?
For very low power use and short duty cycle, can I use a step up transformer to run my 175 on a 110 volt outlet?
Will the welder run fine with out damage if ac powered off a older welder/generator?
Can this lay consistent beads on thin auto metal? I see the more expensive units go down to 25 amps.
where can you get parts for the 175 mig welder
does this machine come with a HOW TO book?
Where is the Eastwood MIG Welder 175 Amp welder made/manufactured?
Do I still get the three year warranty if I buy this product from a distributor and when does it start
Are Lincoln wire spools compatible with this welder?
can i plug this welder 175 or the 200 directly into my garage outlet?? or do i need a step up converter/generator to run it safely. I need a helpful recommendation please.
Is the drive system made of all metal , or meatal / plastic?
need mig 175 repaired wont feed wire continuasly spool gun works good
Can this machine be used for stick welding as well?
Can I use flux cored wire?
When the unit is powered on, is the wire electrically hot when the trigger is not being pressed? Or is it only hot when I press the trigger to feed the wire?
fig d and e 12012 shows blackplastic housing just inside on the bottom left, we need that black plastic housing that holds the devices that allow the gas to comethru the unit the black plastic 4 x 5 inches is broken where the gas line attaches inside so I
Can you spray arc weld with this mig 175 unit?
What is the start-up amp draw as well as the running amp draw? I would like to run this off a 5500 watt alternator w/ 6500 watt surge. has a 220-230 30-amp breaker.
How long is the power cable?
If I have a generator that has a 30 amp 230v line. Could I run the 175 mig welder on that.
I already have a 30amp circuit running 10awg wire, can I just install a 6-50P socket and run off a 30 amp? is 50 amp with 6awg wire required.
Can you provide the voltage output for each letter on the dial? A= ?, B=? , C=?, and so on.. Thanks...Rob
Eastwood MIG Welder 175 Amp with Spool Gun
Item #12012 Brand: Eastwood
- Welds mild and stainless steel, 24-ga. to 5/16"
- Welds aluminum, 14-ga. to 1/4" with included FREE spool gun ($199.99 value!)
- 30-175-amp welding range
- Ships with regulator and hose for optimum MIG welding. Can also be used for Flux-Core welding.
- Powered by 220v current
- Compare to similar welders that sell for over $700
- ETL Approved
- Backed by Eastwood's no-hassle return policy and 3-year warranty. Try it out for 60 days and if you don't like it, return it for a full refund!
About Eastwood MIG Welder 175 Amp with Spool Gun
MIG 175 welder is designed for the professional or weekend enthusiast. The welder comes complete (except for the gas cylinder) and ready to weld 24-gauge to 5/16" mild steel and stainless, plus 14-ga. to 1/4" aluminum. This high-quality MIG welding machine has a 30% duty cycle at 135 amps, and 30-175-amp welding range. Feeds wire at 58"-471" per minute, and has infinitely adjustable wire speed and heat settings. Includes a precision-drive motor, regulator with hose, spool gun (to weld aluminum, 19-gauge to 1/4" plate), wire, tips and accessories...just add your own cylinder of CO2/Argon. "Quick Set" weld chart specifies settings for each material thickness, eliminating guesswork and assuring complete penetration. Backed by Eastwood's no-hassle 60 day return policy and a 3-year manufacturer's warranty.
MIG 175 Welder (89 lbs.)
Spool Gun with 9' cable (works with 2-lb. wire spools only)
MIG Wire 0.030
Aluminum Wire 0.030
Gas Regulator with hose
8' Ground Clamp
8' Gun Cable
3-Year “No Hassle” Warranty
Rated Electrical Input: 210-240 VAC; 50-60Hz; 22AMP
Max Voltage at No Load: 20 V DC
Rated Duty Cycle: 130A@30% duty cycle
Wire Feed Rate: 4.9 Ft/min – 39.3 Ft/min
Wire Sizes: 0.025”(0.6mm) – 0.030”(0.8mm) mig wire or 0.030”(0.8mm) – 0.035” Flux core wire
Welding Wire Spool: 4” and 8” spool
Weight: 62.0Lbs (24.5kg)
Overall Dimensions: 24.4 (620mm) x 12.6” (320mm) x 16.9 (430mm)
Always wear a minimum #10 shade helmet, leather welding gloves and long sleeve shirt and long pants.
3-year manufacturer's warranty.
Amperage and output voltage can be controlled precisely to get the proper penetration required. Wire speed can be infinitely adjusted to gain proper wire fill in the weld pool. This unit has been compared to the leading U.S.-manufactured red welders, with equivalent results at a fraction of the cost. The drive roll mechanism which is the heart of any MIG welder is designed to our specifications and delivers flawless wire feed without skipping or slipping on the wire.
Accessories & Consumables
12211 Contact Tip 0.023
12224 Contact Tip 0.030
12226 MIG Wire 0.023
12227 MIG Wire 0.030
12225 Flux Wire 0.030
12239 Drive Roller
12210 Tweco-Style Nozzle
Auto Darkening Welding Helmet
Large View Auto Darkening Helmet
Customers also viewed:
Perfect welding extension cord that meets all industry and customer standards.Only $109.99
Great for prepping and cleaning any metal surface before welding.Only $5.39
Great for cleaning or prepping metal surfaces for welding.Only $10.69
Tackle heavy metal fabrication with this Plasma Cutter & Welder Combo KitOnly $1,099.99
25-135-amp, industrial-quality, MIG 135 Welder, 120v -- low DIY price!