- Original Hotcoat Powder Coating Gun
Original Hotcoat Powder Coating Gun
Item #10198 Brand: Eastwood
The Original HotCoat Powder-Coating Gun brings the benefits of powder coating right to your home garage or shop.
- Coat and cure in under an hour!
- Easy to apply
- Extremely durable finish
- Quick color changes
- 11,000-volt output
This innovative, inexpensive powder-coat gun helps you do a professional-looking powder coating job right at home. All you need to add are a compressed air source (5-10psi) from a portable tank with a regulator or a compressor), a dedicated electric oven or toaster oven, and powder colors.
About Original Hotcoat Powder Coating Gun
Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.
One 8-oz. bottle of powder (not included) covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat powder coating requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven). Imported.
Original HotCoat Gun with power source and instructions
10021ZP Metal-2-Metal Surface Filler
10078 High-Temp Silicone Plugs, 30 pcs.
10027 High-Temp Masking Tape
43045 Stainless Steel .041" Safety Wire
Hotcoat Bottle and Lid Replacement Set 3 pak
Powder Coating Accessories Kit
Power unit supplies over 9000v DC at 15 micro amps. Plugs into grounded 110-120v AC outlet. Gun requires as little as 0.5 cfm at 5-10 psi. The 50061 Eastwood Air Brush Compressor works well. Fill cup no more than 1/4 to 1/3 full, and wave the nozzle in a circular motion about 4-6" from the surface best results. Do not apply powder into a small boxed area.
(Q) How long does the baking process take?
(A) For improved flow out (less "orange peel"), bake coated parts at 500 degrees F until powder flows out (about 3-4 minutes for light sheet metal parts), then turn down the heat to 400 degrees F for a full 15 minutes.
(Q) What are the electrical requirements?
(A) This HotCoat Gun requires 110-125VAC, 2 amps at 50-60 Hz. Can be used with a voltage transformer such as 220-240VAC to 110-125VAC as long as the transformer can handle 2 amps.
Safety / Instructions
Use Disposable Dust Mask (22055) when handling or applying powder. Powder,like common flour, suspended in the air in high concentrations can be explosive. To minimize any explosion risk - sweep up, do not vacuum powder from the floor. Cure powder in a well ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out.This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator, like our SAS Bandit Respirator (11455 or 11456), cartridges when curing or inspecting flow out progress.
Customers also viewed:
Get started in powder coating today!$199.99
Powder Coating Accessories KitOnly $59.99
Dual Voltage Powder Gun Elite Kit and Oven$379.99
DIY Powder Gun Elite Kit and Oven$329.99
DIY Powder Gun Deluxe Kit and Oven$299.99
Try powder-coating at home! Includes original gun, 4 colors and more
Dual-Voltage HotCoat gun, 4 standard colors plus black and more$259.99
Kit includes our Dual-Voltage Gun, gloss black powder and more!
2 voltage settings allow complete coverage--tight spots to large areas
"Deluxe" HotCoat Powder-Coating Kit includes our original HotCoat gun, making this the perfect starter kit!$149.99