• Home
  • Poly-X, Paint & Rust Removal Disc 4 inch Cup Style
Poly-X, Paint & Rust Removal Disc 4 inch Cup Style is rated 4.5385 out of 5 by 13.
Rated 4 out of 5 by from A great product This is an excellent product for the removal of surface rust, paint and old filler. Take the guard off your angle grinder, put on your welding apron, a good dust mask, ear & eye protection and welding gloves and go to it. This generates a lot of dust so have adequate ventilation. A light touch works best and the disc lasts longer. Disc does not clog and leaves a ready to paint finish on the metal. The open weave allows the disc to cool so the metal is not scorched. Works great even on the newer thin sheet metal panels. Stay away from tar or soft undercoatings, seam sealers and adhesives. A little expensive but probably worth the money in time saved.
Date published: 2010-03-16
Rated 5 out of 5 by from worked as good as expected if not better someone ordered these for me for a car i was working on for them and i was pretty happy with them i went thru 3 of them doing 2 doors 1 hood and a trunk lid on a 66 mustang they held up well didn't leave gouges or heavy scratches in the metal pulls rust off pretty good as well . for heavy pitting rust you might wanna do some media blasting but i didn't wanna sandblast the car itself and get sand everywhere by far the fastest paint removal without blasting in my opinion. leaves a good surface for primer i spray painted a soda can directly after lightly brushing with one of these disk and you couldn't see the scratches. if would recomend ordering extras tho they're handy to keep around
Date published: 2010-12-25
Rated 3 out of 5 by from poor I usually don't write reviews but felt I needed to on this one. Did not realize could add a picture or would have taken it before throwing in the trash. 1st one out of the box self destructed before grinder ever touched metal! Luckily I had on my protective gear. Now I'm limiting the use to a 18V drill to instead the of grinder. Works great for final burnish of metal, but wont cut through 3-4 layers of paint. NOT HAPPY!
Date published: 2013-05-03
Rated 5 out of 5 by from Works really good I purchased a few of these to try. I found them to be very good. I am removing rust and paint from a 50 year old VW that has been repainted. They do not heat up the metal and I find them to hold up for the cost. They do a decent job removing rust as long as it is not too pitted. I liked them enough to make a 2nd order. I use them on my grinder and so far have had no problems.
Date published: 2014-05-09
Rated 5 out of 5 by from Great rust and paint remover This work great on flat surfaces. i was able to strip hood to bare metal in about 40 minutes. it wears out quicker when doing small areas or jagged parts. I have bought several of these and completed the outside of a pickup. Its the lowest cost stripping pad I could find that works this well.
Date published: 2013-04-19
Rated 5 out of 5 by from works great Takes paint off quickly and easily. for best results use very light pressure and let the disk do the work. This keeps the metal cool and saves work. Beware even though the backing pad for this product says 11k rpm i have had one explode. if you use this on an angle grinder beware of that.
Date published: 2013-04-03
Rated 3 out of 5 by from little overpriced but great product If you are doing a complete car invest in the 7" one, its worth it. This one is great for the small corners or hard to reach areas. Wears out really fast so get plenty at once.
Date published: 2011-08-12
Rated 5 out of 5 by from Let it do the work. I bought several (10 I think) of these to completely strip a 1976 Ford Maverick 2 door that had full paint AND Rust Bullet sealer on the metal. I used a Harbor Freight 4 inch grinder and had to add 3 small strips of duct tape to each inner section of the wheel to ensure they would seat on the collet correctly without slipping - no biggie. Doesn't take a lot of pressure, and don't try to hold them at an acute angle or else you end up with the edges thinned out with a thick center section. A slight angle is all that is needed and you end up with even wear over the entire disc. You can use the disc clean down to the plastic mount it is on, so don't be afraid to take it as far down as possible to get your money's worth. Very little heat on the metal unless you stay in one spot. Cuts very nicely, and just let it do the work. Don't go real fast, and yet you don't have to go real slow unless your surface it is cutting is pretty thick. In which case just slow down and let it work. If need be cut the top coat and then cut the bottom with a 2nd pass - works better & lasts longer than trying to do it all at once. Good product I think.
Date published: 2015-04-13
  • 2015-04-18T08:50CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_13
  • loc_en_US, sid_13395, PRD, sort_relevancy
  • clientName_eastwood

Poly-X, Paint & Rust Removal Disc 4 inch Cup Style

Item #13395 Brand: A W Tools

Abrasive Cup Disc works with
your angle grinder to strip and clean metal


Attach this Abrasive Cup Disc to your drill to effortlessly strip and clean metal Cup-style cleaning disc with recessed center-mounting hole is aggressive enough to strip paint and rust without removing excessive metal.
  • 4"(100 mm)-diameter disc
  • Silicone-carbide-impregnated abrasive
  • Open mesh resists clogging
  • 6500-rpm maximum

More info...

About Poly-X, Paint & Rust Removal Disc 4 inch Cup Style

Use it for rust removal, weld clean-up, and paint removal. Open-mesh, silicone-carbide-impregnated abrasive resists clogging and constantly exposes fresh abrasive for consistent cutting action. 7/8" steel-reinforced mounting hole.

Customers also viewed: