Calyx Manifold Coating 3 oz

Customer Reviews

(Posted on 1/25/10) good stuff
Review by frank

Quality
Price
Value

great stuff really work's

(Posted on 1/26/10) great stuff
Review by camcam

Quality
Price
Value

got word of this product a car show and tried it. i have to say that it did a pretty good job.i was thinking of taking down manifolds .too much work,so i put the dressing on,what a difference,looks like it came from the assembly line.i recommend putting on a latex glove on ,or using a toothbrush.

(Posted on 4/17/10) Great product at a great price
Review by Paladin06

Price
Value
Quality

Every once in awhile you come upon a product that exceeds your expections. Well this is one of those products. It's very easy to apply, very affordable and most importantanlt it looks great. My before and after pictures speak for themselves. You better get some NOW!!

Thanks Eastwood.

(Posted on 6/9/10) well worth the money!!
Review by Sean

Value
Quality
Price

Just check out the picture! This is a coating remember, it rubs in and you buff it like you would waxing a car. And it doesnt come off.. Its freaking amazing

(Posted on 6/17/10) great product
Review by ERIC

Value
Quality
Price

Made the manifolds look like new, unbelievable what a little jar like that can do.

(Posted on 7/15/10) Overall, fairly positive
Review by misercola@yahoo.com

Value
Quality
Price

First application went on great and looked terrific -- just like when the car rolled off the assembly line 50 years ago.

Ive subsequently had to reapply it twice to the exhaust manifold on the passenger side where it seems to fading in one area. Will continue to watch it and see if it persists.

(Posted on 7/23/10) multi-use
Review by nufsaid

Value
Quality
Price

It works great on manifolds, as others have stated, but you would be amazed how well it works on suspension and driveline raw metal pieces!! ie; drive-shafts, uprights, tie rod ends, u-joints, half shafts, steering boxes, carb & trans linkage, rear-end housings, just about anything that came from the factory in bare metal!!!
Touch up is as easy as it gets, just rub in a little more product-amazing results.
I believe the secret to success with this product is media blasting, and clean-clean-clean!! Parts that won't be exposed to much heat, should be allowed to bake in the sun or in an oven, for a couple of hours to cure.

(Posted on 6/21/11) Fantastic Results in about an hour
Review by GHolbrook

Price
Value
Quality

OK, I saw the advertising pics and read some mixed reviews on various forums, but wow was this stuff impressive. I left the manifolds on the car and literally just grazed over the easy to reach places really quickly with a wire brush.
Heres a tip- I found within a couple of minutes, that using a rag was not the way to go. Use something that won’t shred (Denim pieces form old jeans works great). Make sure you have a TOOTHBRUSH. The toothbrush will make this really quick. Just use your rag (or denim piece) to spread some of the Calyx on the manifold (a little heavy), then use the toothbrush to “brush” the stuff into the pores and to get the areas that are impossible to get well with a rag. You will probably want to pull the spark plug wire (leave the plugs in place) from the area you are working in just so you can access everything easily and get into the back area and grooves. The toothbrush will make this so amazingly fast it should be in the instructions! Be generous with the application of the stuff…you won’t run out.
The little jar goes a long way, I have enough left over after doing my BBC manifolds for another 5 or 6 pairs easily.
When done, take your car for a spin around town to heat the manifolds up.
The transformation from splotchy brown/tan old manifolds to factory new looking in an hour is a “must do” project. Just go a cheap toothbrush (I had “hard” bristles and it worked really well). If you decide to go without the toothbrush and just use a rag, it will probably take 3 to 4 hours to rub in and get the tops, grooves etc well. Still well worth the effort.
I do hear that the coating will need to be touched up after a couple years, so save the leftovers..… I’ll probably have to buy more since friends and family saw how mine looked and I now everyone wants the classic car manifolds done.

(Posted on 10/15/11) Nice finish but requires constant touching up
Review by Cor66vette

Value
Quality
Price

At first the finish was awesome. Smooth, silky, even, and clean looking but at the same time not exaggerated or flashy. Sorry to find out that the finish didn't stay smooth for long. Some of the reviews said manifolds needed touching up after a couple of years? In my case would you believe almost immediately? I retouched three or four times within a week. I even explained this to Eastwood and they were good enough to send a second cup so I could see if the first was bad. Same problem. I could not experience a finished product. I do not recommend this Calyx coating but I do recommend Eastwood. They are top shelf.