Versa Cut 40 External Nozzle

    Item #13787 Brand: Eastwood

    Details

    This is a replacement external nozzle for Eastwood's Versa Cut 40 Plasma Cutters. This is the black nozzle that holds the electrode and nozzle on the end of the torch. Includes 1 piece.

    About Versa Cut 40 External Nozzle

    This is a replacement external nozzle for Eastwood's Versa Cut 40 Plasma Cutter.This is the black nozzle that holds the electrode and nozzle on the end of the torch. Includes 1 piece.


    Contents

    Includes: 1 Replacement External Nozzle


    Application

    This is a replacement external nozzle for Eastwood's Versa Cut 40 Plasma Cutter.This is the black nozzle that holds the electrode and nozzle on the end of the torch. Includes 1 piece.


    Customers also viewed:

    Customer Reviews

    8 Item(s)

    per page
    Could be better (Posted on 6/8/2014)
    Review by Ted
    Price
    Value
    Quality
    These nozzles are rather fragile. If you get too close to grounded metal from the side an arc will jump across from the metal to the metallic parts of the tip and burn it up. Sometimes it is difficult to use the cutter without harming the nozzle. Perhaps if the insulating portion of the nozzle was made of tougher stuff, say ceramic, they would last longer.
    Burns FAST! (Posted on 6/3/2014)
    Review by David
    Price
    Value
    Quality
    I had probably 2 hours on the machine and already had signs of premature burn through that I have not encountered on other cutters.

    The price was OK if the nozzle lasted longer but based on the length of actual use time I think the price is a bit high...
    Short service life (Posted on 2/24/2014)
    Review by Bruce
    Quality
    Price
    Value
    This nozzle is made of some type of bakelite and burns up pretty easily especially near a right angle. A somewhat pricey replacement if you burn them up regularly. Other than that, the Versa cut 40 is quite adequate for my needs.
    Versa 60 consumables are too pricey (Posted on 9/7/2013)
    Review by Denis
    Quality
    Price
    Value
    These nozzles work fine IF you have a good 'stand-off' which prevents the shorting and burning of the nozzles. and, since the spring-wire standoff that comes with the Versa 60 is of limited value, what you get are burned nozzles. And, these standoffs sold by Eastwood are way overpriced and not a great design. I found a very nicely designed standoff on Ebay, or if you have a lathe you can make one. At any rate all the consumables for the Versa 60 are too pricey, but when you need them.... try looking elsewhere first.
    poor (Posted on 9/1/2013)
    Review by roberto
    Price
    Value
    Quality
    Does not work on v cut 60 talked to Ed in tech services. Sent the two I ordered back
    poor quality (Posted on 12/6/2012)
    Review by Randal
    Quality
    Price
    Value
    Burned away after very little use. Agree with willy d that it should be brass & more pointed.
    useless (Posted on 11/4/2012)
    Review by willy d
    Quality
    Price
    Value
    tried to use a metal guide for a straight cut, heat from plasma melted tip. the tip needs to be maid out of brass and more pointed for a closer cut when using a guide.
    poor quality (Posted on 10/29/2011)
    Review by melvin
    Quality
    Price
    Value
    After very little use this plastic type material external nozzle has melted/burned . Eastwood said this is a consumible item.$12.00.expensive for very little use. Eastwood did not offer to replace item under warrenty.unit is a week old and used about 20 min.

    8 Item(s)

    per page

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register