Eastwood Contour Aluminum Repair Compound 25.3 oz

    Item #13518ZP Brand: Eastwood

    Price
    Value
    Quality
    7 Review(s)

    Details

    Contour™ Repair Compound is reinforced with aluminum for a stronger, corrosion-resistant repair Eastwood's uniquely formulated filler is fortified with aluminum particles to produce a repair with extra strength, corrosion resistance and durability in galvanized steel and aluminum.
    • Superior corrosion resistance and adhesion
    • Repair factory-leaded seams and high-strength applications
    • Perfect for areas prone to moisture
    • Includes hardener

    About Eastwood Contour Aluminum Repair Compound 25.3 oz

    A uniquely formulated filler fortified with aluminum for strength, corrosion resistance and durability. Use to repair factory leaded seams and high strength applications as well as areas prone to moisture. Its corrosion resistant properties prevent rust from coming through the repair. Appliesdirect Includes Liquid Hardener.


    Contents

    Filler: 25.3 Ounces/750 mL Hardener: .5fl oz/14mL


    Accessories

    13521 ZP EW Contour Glazing Putty 10041Z PRE Painting Prep 13919 Eastwood Filler Spreaders 31273 Eastwood Filler Mixing Board 31160 Dura Block Sanding Boards 21538 Larry Lyles Body Work DVD 43579 DA Orbiting Sander 43120 Eastwood Work-Fender Stand


    Application

    Thoroughly mix desired amount of material with liquid hardener. Using a clean spreader, fill to desired level. Do not exceed 1/4" depth. Allow to cure for at least 15 minutes before sanding. Abrade with 40-80 grit and follow up with 120 grit to achieve desired contour. Final finish with finer abrasives. If necessary, apply Eastwood’s 13521ZP Contour™ Glazing Putty for final finishing. Topcoat with quality primer, such as Eastwood’s Epoxy or Urethane Primers.

    CAUTION: Do NOT return catalyzed material back into can. To avoid contamination, seal lid tightly after each use. Store in a cool dry place.


    Safety

    Always wear eye, skin and resp[oratory protection when using this product always apply in a well ventilated area. consult MSDS and product label for specific safety warnings


    Warranty

    Made in Canada to Eastwood's strict specifications and quality standards


    Application

    Surface must be clean and free of wax, grease and debris. Abrade surface using 36 grit, or finer. Thoroughly mix desired amount of material with 2% liquid hardener. Do not exceed 1/4" depth. Allow to cure 15 min before sanding. Abrade with 40-80 grit and follow up with 120 grit to desired contour 5. If necessary, apply Eastwood's Polyester Glazing Putty (13521zp) for final finishing. Topcoat with quality primer such as Eastwood's Epoxy or Urethane Primers. Do NOT return catalyzed material back into can.


    Customers also viewed:

    Customer Reviews

    7 Item(s)

    per page
    does not harden (Posted on 6/8/14)
    Review by DAVID
    Price
    Value
    Quality
    poorly hardens. even with double and triple the amount of hardner, still risky as to wether it will harden up. Will not use again. I should have looked at the reviews before I purchased
    Poor (Posted on 2/27/14)
    Review by Carl
    Quality
    Price
    Value
    Product came with no hardener after I had put a message with order to send an extra tube after I had read reviews that other people had problems with not setting up. I applied on new metal that had been ground than sanded with 36 grit and cleaned with lacquer thinner the product instructions are a little unclear to me when it said 2percent hardener I would have liked for it to say add so many drops I think that would work better for me, but anyway Ithe first batch I mixed would not harden so I doubled it mixed another batch it did better but when I sanded it peeled and would not feather edge it was cool in the garage about 50 degrees maybe that had some effect on it but the other filler worked fine. I don't think I would buy this product again I wish I had listened to the other reviews.
    Long Set Time (Posted on 9/21/13)
    Review by Garrett
    Price
    Value
    Quality
    Thoroughly mixed proper amounts as directed and applied to pre prepped clean sheet metal. 6 hours later and still tacky to touch. Now waiting overnight and will check in morning. Looks like good product by may require greater amount of hardener.
    Don't trust it (Posted on 9/10/13)
    Review by Chad
    Price
    Value
    Quality
    I along with at least one other customer had problems with the filler not setting up properly. I followed the hardener to filler ratio and 4 hours later it was still a semi hard, sticky, non-sandable mess. I tried to contact Eastwood several times, for over a week, yet never received an answer. If you double the hardener to filler ratio it works, however there is no way of knowing if that will compromise the integrity of the filler. I would NOT recommend this product until issues have been resolved.
    Works...However... (Posted on 8/24/13)
    Review by Greg
    Price
    Value
    Quality
    Followed hardener to filler ratio and 12 hours later had to scrape a semi solid mess off my project. Tried again doubling the hardener ratio and filler set after a couple of hours. Once set filler performed as expected, sanded well and edges feathered smoothly. Now I have a half can of filler and no hardener
    ok (Posted on 5/26/13)
    Review by thomas
    Quality
    Price
    Value
    i wish i had used this years ago .i love it .waterproofs.great on fiberglass.i will always use the eastwood contour repair compound for all my projects and repairs.thanks again
    Good, so far (Posted on 3/12/13)
    Review by Yamabeaver
    Price
    Value
    Quality
    Can showed up with multiple dents in it, no damage to shipping box, was this warehouse damage or???
    Seals were still in place, so I have faith in Eastwood products it will still work as promised, haven't used it yet.

    7 Item(s)

    per page

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register