Eastwood Gray Urethane Primer Surfacer

    Item #Urethane Primer Surfacer

    Details

    Eastwood's Urethane Primer Surfacer is formulated for a wide range applications. Provides quick and easy sanding along with exceptional holdout and fast film build. An excellent choice when using the Eastwood Paints. Requires 4:1 50241 ZP Activator.

    About Eastwood Gray Urethane Primer Surfacer

    "Eastwood's Urethane Primer is formulated for a wide range" "applications. Provides quick and easy sanding along with exceptional" "holdout and fast film build. An excellent choice when using the Eastwood" "Paints " "Requires 4:1 50241 ZP Activator"


    Accessories

    50241ZP 4:1 activator
    51550 Concours HVLP paint gun
    10041zp PRE Painting prep
    51686 Concours HVLP detail gun


    Safety

    Always wear eye, respirator and skin protection use in a well ventilated are consult MSDS for specific warnings precautions.


    Instructions

    Click here for product information sheet


    Customers also viewed:

    Customer Reviews

    Items 1 to 10 of 18 total

    per page
    1. 1
    2. 2
    Great Primer! (Posted on 5/15/2014)
    Review by Matt
    Price
    Value
    Quality
    Sprayed smoothly from an inexpensive HVLP with no reducer necessary. Flowed out great.
    I sprayed this without a paint booth, but was fortunate enough to have ideal temperature when spraying. The results far exceeded my expectations.
    Decent product (Posted on 4/22/2014)
    Review by Ryan
    Price
    Value
    Quality
    I had to reduce this product quite a bit. It almost dries to fast but that could have been my reducer. It fills great and sands very easy compared to other brands I've used. I would probably be using this primer again in the future.
    A bit of a learning curve for the beginner. (Posted on 12/14/2013)
    Review by William
    Quality
    Price
    Value
    Goes on a little thicker than the spec sheets indicate. Comparing it to the other Eastwood products, this does not perform exactly as the spec sheets would indicate. It is bit more viscous and requires a 1:2 needle in the Concours Eastwood Gun or to open the needle all the way on a gun with a 1:4. All other adjustments on the gun should be open as well and dialed in as needed. I recommend you use 25 psi at the gun to start if you have a decent to high quality gun. Once you have the gun dialed in, this product works great and fills in nicely after the second pass. A third pass and most light imperfections are gone.
    A Favorite (Posted on 12/4/2013)
    Review by David
    Quality
    Price
    Value
    I sprayed this with the "Contour" gun with a 1.8 nozzle. I found I had to reduce it with one part reducer to get it to spray well. It fills minor imperfections beautifully and sands to a very smooth finish. The adhesion is excellent. Would definitely use it again.
    Poor Flow with out reducing, but easy Sanding. (Posted on 7/24/2013)
    Review by Kurt
    Quality
    Price
    Value
    I shot this with a DeVbliss Starting line gun with the 1.8 tip. It did not flow very well, and I had to reduce it 20%. Other wise it was like shooting mud. If not reduced it came out very textured, and added sanding time. Like the tech sheet says, it was sandable after 30 minutes or so. Was easy to sand, but because it was very textured, it was quite a bit of block sanding starting with 120, and moving up to 400. Once I thinned it out, it was super easy to shoot, and sand. The Tempature in my shop was around 80, so that might have had something to do with it. I ran out of this and picked up some Nason 2k Primer and I felt like the 2 were very close in terms of shooting and sanding, but this product was a little cheaper. When I run out of the Nason 2k Primer, I will rebuy this.
    Good but not great (Posted on 8/22/2012)
    Review by Aaron
    Price
    Value
    Quality
    Warning! You have to buy the thinner because this product is way to thick to spray. Goes on nice after thinned about 15% with the Zero VOC Thinner. Real nice as a sealer. Sands well.
    2K Catalyst works great (Posted on 8/11/2012)
    Review by big dog
    Price
    Value
    Quality
    I just finished priming abunch of parts today.Catalyst mixes and blends excellent..mixed with the primer leaves a nice hard finish that easy to sand..got my vote.Thanx Eastood another easy to use product..BD
    Good product - very satisfied (Posted on 7/12/2012)
    Review by Vinny I
    Price
    Value
    Quality
    I have used other primers, more expensive items from a local auto paint store. This product flows on easily, covers well and cleans up with a minimum of work. It sands nicely, providing a good substrate for the one step urethane paint I've used with excellent results. Bear in mind, I'm a do-it-yourselfer with only some painting experience, but this product works well. I highly recommend it!
    Good stuff (Posted on 5/1/2012)
    Review by Tractrfxr
    Price
    Value
    Quality
    Best primer I have used for the price it really works great, sands good and has great filling properties thanks Eastwood for good products.
    Works great (Posted on 4/30/2012)
    Review by tractrfxr
    Price
    Value
    Quality
    Sands easy and the filling properties are good

    Items 1 to 10 of 18 total

    per page
    1. 1
    2. 2

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register