2K Ceramic CB Gloss and Activator 1 Qt.

Item #50544 ZP

Quality
Price
Value

1 Review(s)

Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations; check with your local and state guidelines as some areas may have stricter regulations than others.

Details

Professional-Grade 2K Ceramic Chassis Black is our toughest, most durable chassis coating Eastwood's 2K Ceramic Chassis Black Gloss is a super-durable coating that's not only beautiful, but it's tough as nails. Our own formulation imbeds finely ground ceramic particles into a high-quality 2K (2-component) 4:1 urethane base, making it highly chip- and chemical-resistant, UV-resistant, and easy to spray; dries quickly.

Full and partial frames
Floor pans/undercarriages
Suspension components
Off-road and race vehicles
Roll cages

About 2K Ceramic CB Gloss and Activator 1 Qt.

Customers like you asked for a tough, super-durable chassis coating, so our R&D team developed Eastwood's 2K Ceramic Chassis Black. It's a chip- and chemical-resistant coating with incredible UV resistance, fast dry times and a finish that's second to none. It's easily applied with an HVLP spray gun (1.5mm to 1.7mm tip) and, when laid over Eastwood's 50242ZP Epoxy Primer, gives you a no-worry finish that will last and last. Withstands up to 300 degreesF. Each quart covers 50 sq. ft. (a full-frame vehicle requires 2 quarts).

Product information sheet - Click Here

Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations; check with your local and state guidelines since some areas may have stricter regulations than others.

One catalyzed quart of Eastwood 2K Ceramic Chassis Black Gloss covers about 50 square feet in 2 coats (a full-frame vehicle requires 2 quarts). The 21854Z Activator (8 ozs.) is sufficient to catalyze one quart of Eastwood 2K Ceramic Chassis Black Gloss.

Eastwood 2K Ceramic Chassis Black is easily applied with your HVLP gun using a 1.5mm or larger nozzle. Provides complete hiding in 2 coats; allow 10 minutes between coats. Refer to product label for more complete application directions and safety information. Can be applied directly over our 50242ZP Epoxy Primer after 60 minutes to 5 days, without scuffing.

(Q) Can Eastwood 2K Ceramic Chassis Black be applied directly over other finishes?
(A) Generally 2K Ceramic Chassis Black can be applied over most thoroughly cured finishes (finishes that cannot be indented with a thumbnail). Scuff first with 320-600-grit sandpaper and test a small area before coating the entire area. If lifting occurs, remove the lifting paint, sand the surrounding area, and seal the surface by priming first with 50242ZP Epoxy Primer mixed with 50243ZP Epoxy Primer Catalyst. NOTE: Eastwood Epoxy Primer can be reduced up to 20% with 50104ZP Zero-VOC Urethane Paint Reducer to use strictly as a sealer.

Always wear appropriate eye, skin and respiratory protection when using this product. Always apply in a well-ventilated area, away from open flames. Consult MSDS for specific safety warnings and hazards.

Customer Reviews

Poor chip resistance (Posted on 12/20/11) Review by Bruno

Quality
Price
Value

I used the gloss black over PPG epoxy primer. I first spayed my frame using 10% reducer. I used a Sharpe paint gun with a 1.6 tip. the overspray was excessive and left a rough almost silvery finish on parts of the frame. I sanded the frame with 320 grit and resprayed months later using more reducer this worked much better and left a nice finish. I used this paint because it claims to be chip resistant, it's not. This paint chips with the slightest contact with anything. I would not use it again, not worth the cost.