Eastwood Master Blaster-Dual Blaster

    Item #11737 Brand: Eastwood

    Quality
    Price
    Value
    19 Review(s)
    Heavy Item - Special shipping charges may apply.

    Details

    Eastwood "Master Blaster" Dual Blaster lets you switch "on-the-fly" between soda and abrasive media, or a combination of both! Eastwood's exclusive combination soda blaster and abrasive blaster features our patent-pending "Mixing Valve" that lets you switch instantly between full-flow soda media for gentle-to-mild cleaning or paint removal on stainless, chrome, aluminum or fiberglass, and full-flow aggressive abrasive media for removing even the heaviest rust from frames and suspension components. Also allows infinite "on-the-fly" mixing of the two medias for controlled removal of paint or rust/corrosion on virtually any surface. A must for the serious restorer!
    • Switch between medias in seconds, or mix at an infinite ratio between the two
    • On-the-fly switching or mixing saves you money and cuts blasting times in half
    • Includes extra nozzles and moisture separator
    Click Here to see the winners of the Rename the Dual Blaster Contest!

    About Eastwood Master Blaster-Dual Blaster

    Use soda blast supplies to remove coatings on delicate substrates such as fiberglass, chrome or stainless...then easily switch on-the-fly to harsher abrasives such as crushed glass, glass bead or aluminum oxide to blast through heavy scale, rust or multiple coatings. It's a must-have tool for restoration and maintenance shops where rust and paint removal are issues on multiple surfaces such as fiberglass, steel, aluminum, etc. Each of the fully welded, powder-coated tanks holds 100 lbs. of abrasive media (75 lbs. of soda), and works on as little as 10 cfm at 90 psi. 10-ft.-long, heavy-wall blast hose. Imported.


    Contents

    Unit weighs 80 lbs., and includes extra nozzles and moisture filter.


    FAQs

    (Q) What size of compressor is required?
    (A) Minimum 10-cfm, 90-psi compressor.

    (Q) Which nozzles can I use with the Master Blaster?
    (A) Use any of these nozzles: 51556 (2.0mm), 12111 (2.5mm), 12112 (3.0mm), or 51557 (5.0mm)
    .


    Safety

    WARNING: Pressure blasters and blast cabinets emit abrasive particles under high pressure. Adequate respiratory, eye, and body protection must be utilized at all times during product operation. Inhalation of silica-based media particles have been known to cause cancer and other deadly diseases and must be avoided. Always wear NIOSH-approved respiratory protection when operating the equipment.


    Warranty

    1-year mfr's. warranty against defects.


    Instructions

    Click here for product instructions


    Accessories & Consumables

    Replacement Parts

    51556 2.0mm nozzle (requires minimum 6-cfm 60-psi compressor)
    11931 Blast Pipe
    11917 Moisture Trap
    11914 Outer and Inner Valve
    11902 3-Way Manifold
    11897 First Air Pipe
    11900 Second Air Pipe
    11896 Seal Ring

    Accessories

    Deluxe Blasting Hood
    Ground Glass, 40-70 Grit
    Glass Bead, 100-170 Grit
    Glass Bead, 70-100
    Aluminum Oxide 60 Grit
    Aluminum Oxide 90 Grit
    Automotive M Soda Media
    Automotive XL Soda Media
    Rust Removal XL Soda with Aluminum Oxide
    After Blast, 1 Gallon


    Customers also viewed:

    Customer Reviews

    Items 11 to 19 of 19 total

    per page
    1. 1
    2. 2
    Eastwood Appreciates your Feedback (Posted on 5/20/11)
    Review by Eastwood
    Value
    Quality
    Price
    We've listened to your feedback and made improvements to the Master Blaster based off of this feedback. This product is backed by our Satisfaction Guarantee - if you are unhappy with your purchase, contact us and we will make it right!
    Soda blaster broke during assembly (Posted on 2/6/11)
    Review by Ronald
    Price
    Value
    Quality
    I am not sure how well the dual blaster works as the "T" fitting on the soda side of the Master Blaster broke during assembly rendering the entire unit useless. I have been unable to locate another fitting so I may try my blaster. This is not the usual sort of quality I have come to expect from Eastwood products.
    Good, but not great (Posted on 1/24/11)
    Review by Bravoman
    Price
    Value
    Quality
    When its working- it works fairly well. I had several blockages, I needed to run an industrial dessicant to get it running smooth and moisture free. Switching from abrasive media to soda is nice and smooth, The clamps and valves are poor quality, I expected better from Eastwood. It is slightly over priced. If I had to do it over again I would try my luck with some Habor Freight equipment- but I have been dissappointed there before.
    I am satified but expected more. The face shield/hood they supply is garbage- thin, flimsy, poor protection. If you value your eyes buy one of better quality. I rarely post reviews, but this needed to said.
    DM
    Make Sure you have enough pressure (Posted on 1/16/11)
    Review by A919
    Price
    Value
    Quality
    I bought the device along with two bags of media. Unfortunately my compressor could not keep up with the demand of air. I kept on trying to let it recharge and blast away little by little. Not a good idea, it uses the same amount of media as if it were at full pressure but does nothing, All I got cleaned was a quarter of the bumper. For 80 dollars in media it was not a bargain.
    Dual soda blaster (Posted on 2/25/10)
    Review by Irwintoys
    Quality
    Price
    Value
    Great product but took 2 hours to assemble. Under loop frame mounting holes were predrilled in wrong location,so we had to drill new holes to mount frame correctly to blaster. Inlet manifold valves were preassembled unside down so hoses would not connect. We had to dissasemble valve assembly and reassemble in correct locations. Once completed Blaster is awesome. i would recommend this unit.
    This Blaster Fill all My Specs (Posted on 12/8/09)
    Review by Milton
    Price
    Value
    Quality
    Great Item super easy to Assembled. I start to used in my powder coating shop make me the job super easy because when I needed in heavy jobs or in other more delicate' s you have all you need in your hand open more soda or more media and that's all great product very helpful .
    Ist class tool (Posted on 11/17/09)
    Review by jcautocraft@yahoo.com
    Value
    Quality
    Price
    I have been restoring and building cars for 37 years. This is the best for the money tool I have had the pleasure to use. Put a regulator on the inlet and works perfectly @ 100psi or less. Used both abrasive and bi-carb tanks and was amazed at the results. Bravo to Eastwood. Thanks JC
    Dual Soda Blaster (Posted on 10/25/09)
    Review by Gray
    Quality
    Price
    Value
    A big thumbs up! Some fittings had been lost in transit to England(Customs no doubt) but were easily replaced. Assembled kit quickly, followed the instructions, and got great results in seconds of use on vintage BSA Motorcycle engine cases (that had more than their fair share of heavy hand painted layers) Having a good supply of air is very important so have upgraded to a diesel compressor for more steady pressure and cfm. Very good addition to workshop, great service from Eastwood Too! Buy one!
    Good Product for the Price (Posted on 10/16/09)
    Review by DV
    Value
    Quality
    Price
    Product works well. The only thing I'm a bit disappointed with is the clamps used, not great quality. I have also run the blaster twice and blew a hole through one of the hoses on the abrasive side.. Maybe too much pressure.. I'm going to see if Eastwood will replace the hose.
    Other than this, it's a real nice tool to have. I'm restoring a 66 Ford and I have alot of blasting to do.

    Items 11 to 19 of 19 total

    per page
    1. 1
    2. 2

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register