Factory Gray Hi-Temp Coating

    Item #10395 Factory Gray Hi-Temp Coating

    Save when you buy 3 or more.

    Details

    Factory Gray Coating replicates the look of cast iron on manifolds and headers.
    • Temperature resistant up to 1200 degrees
    • Available in pints or aerosol
    • Brush or spray-on application

    About Factory Gray Hi-Temp Coating

    Now the same great 1200 degree performance of our original High Temp Manifold Coating is available in convenient aerosol packaging. Each can is sufficient to coat 2 standard cast iron manifolds or about 6 square feet. 2 cans recommended for header systems.


    Pint Information

    This pint of Factory Gray Coating replicates the look of cast iron on manifolds and headers. Easy brush-on application with the included disposable brushes or sprayable as is using our Pro Portable Sprayer (10387Z) or your jamb gun.


    Detailing Kit Information

    Factory Gray Exhaust Detailing Kit - 1 each of Factory Gray High Temp Coating (34105Z), Exhaust Paint aerosol (10020Z) and a Pack of 3 disposable foam brushes (34152). The pint of High Temp Coating provides enough material to cover one pair of exhaust headers or a few pairs of cast iron manifolds. One aerosol can of Silver Exhaust Paint covers about 6 square feet.


    Safety

    Contains Toluene 108-88-33 1, 1, 1, 2-Tectraflourethene (HFC-134A) 811-97-2, Stoddard Solvent 8052-41-3,Aluminum Flake 7429-90-5,Mineral Spirits 64742-88-7, Phenylpropyl Silsesquioxanes 68037-90-1,Toluene 108-88-3,Carbon Black1333-86-4. Keep away from heat, sparks & open flame. Use with adequate venting. Vapor is harmful. Harmful or fatal if swallowed. If swallowed, do not induce vomiting. Call a physician immediately.Avoid prolonged skin contact & breathing of vapor mist.Warning: This product contains a chemical known to the State of California to cause birth defects and other reproductive harm.


    Customers also viewed:

    Customer Reviews

    9 Item(s)

    per page
    excellent paint (Posted on 3/22/2014)
    Review by Victor
    Quality
    Price
    Value
    has hold up well and not burned off manifolds. Very little rust bleed through. Brush on paint is better then spray, easier to touch up.
    very good (Posted on 8/19/2013)
    Review by duvall
    Quality
    Price
    Value
    Very good product if applied correctly.
    This stuff is the shizzle!!! (Posted on 5/13/2012)
    Review by 61forfun
    Price
    Value
    Quality
    I have used this stuff for years. My old Camaro and 61' Impala were done 10 years ago and this stuff still looks awesome. The appearence looks like fresh cast iron. I am building a 61' Dodge Pioneer with a long ram setup and recently purchased another can of this stuff to make my underhood experiance glow!!! Thx Eastwood for another excellent product!
    Excellent (Posted on 3/28/2011)
    Review by KL
    Quality
    Price
    Value
    I have tried numerous "stove paints" and other high temp coatings with dismal results. All were quickly cooked and flaked off within a very short time. The Eastwood Factory Gray Hi-Temp Coating is the first high temp exhaust coating that actually works. I used the pint brush-on for the manifold and exhaust pipe on my tractor. It still looks great after several months of hard use.
    A must for any engine swap! (Posted on 1/29/2011)
    Review by Athan
    Quality
    Price
    Value
    I picked up a can of this product a few years back for some exhaust manifolds for a 68 Pontiac. Years later the manifolds still look great! You put all that work into a new engine, don't just put the old manifolds back on there without this coating. Bare manifolds will oxidize over time and give you an eyesore in the engine compartment. Be sure to beadblast the manifolds before prep! Thanks Eastwood!
    Good (Posted on 5/7/2010)
    Review by Gerard
    Price
    Value
    Quality
    Easy to apply in two thin coats. Also used on rear brake drums. Will do front calipers next. Make sure you are outside when you start engine to dissipate fumes from manifolds. Looks good and would recommend to others.
    Great manifold coating (Posted on 2/23/2010)
    Review by mrfirebird73
    Value
    Quality
    Price
    Goes on easy but could be a little darker and cheaper. Other than that it is a very good coating. Very pleased and will recommend.
    Great coating for your exhaust manifold (Posted on 1/25/2010)
    Review by Jukey3
    Quality
    Price
    Value
    Spray went on easy and adds a really nice look to my cast iron exhaust manifold. Really dresses up the engine! Highly recommended.
    Good (Posted on 8/17/2009)
    Review by stan
    Quality
    Price
    Value
    It looked good,went on easy. Would buy again.

    9 Item(s)

    per page

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register