Eastwood Dual Voltage Powder Gun Starter Kit

    Item #11698 Brand: Eastwood

    Price
    Value
    Quality
    20 Review(s)

    Details

    Our best value! HotCoat Powder-Coating Starter Kit includes our Dual-Voltage gun for greater versatility With our dual-voltage HotCoat powder coating gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop! Besides the dual-voltage gun, this kit also includes gloss black color, plus all the other powder coating supplies else you'll need (except compressed air and a dedicated oven) to achieve expert results.
    • Extremely durable finish
    • Coat and cure in under an hour!
    • Easy to apply
    • Quick color changes
    • Economical

    About Eastwood Dual Voltage Powder Gun Starter Kit

    Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

    One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the over-sprayed powder. Contains no environmentally harmful solvents. HotCoat Powder Coating System requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).

    (See "Contents" tab for all the specific powder coating supplies included in this Dual-Voltage kit.)


    Contents

    11676 Eastwood Dual-Voltage HotCoat Gun
    1/2-lb. Black Gloss Powder
    51558 Powder Chip Color Chart
    10078 Reusable Hi-Temp Silicone Plugs
    10027 Hi-Temp Masking Tape (1/2" x 36-yard roll)
    43045 1-lb. Stainless Steel Hanging Wire
    34066 In-Line Air Filter
    3 Empty Powder Bottles with Screw-On Tops


    Specs

    Accessories

    10041Z PRE Painting Prep
    51081 Metal Wash Metal Prep
    19418ZP Fast Etch Rust Remover and Metal Prep
    20473 2-Stage Air Dryer System
    58111 Pack of 20 Hooks
    58112 Silicone Cap & Plug Kit
    11477 Infrared Thermometer
    10590 Infrared Curing Lamp


    FAQs

    (Q) Can I use my household oven?
    (A) No, you cannot use an oven that will be used to cook/bake food.

    (Q) How long do I bake/cure the part?
    (A) 20 minutes at 400 degreesF.

    (Q) Can I remove the powder coating?
    (A) Yes, use 12849 Powder Coat & Paint Dissolver (Qt.) or 12850 Powder Coat & Paint Dissolver (Gal.) .

    (Q) How do I know what the colors will look like?
    (A) Order Eastwood's 51558 HotCoat Powder Coating Chip Chart (free in our kits).


    Safety

    Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh cartridges when curing or inspecting flow-out progress.


    Warranty

    1-year mfr's. warranty against defects.

    Designed, engineered and tested to Eastwood's specifications.

    Final product imported.


    Customers also viewed:

    Customer Reviews

    Items 11 to 20 of 20 total

    per page
    1. 1
    2. 2
    a great gun (Posted on 3/4/13)
    Review by bandb
    Price
    Value
    Quality
    This is a perfect unit for the beginner. It works very well and is 100% worth the amount charged. My first time powder coating went extremely well and am ready to offer this service to others wanting a great shine for a reasonable price. Thanks Eastwood for what you do. Brad in Canada
    Great addition to my shop (Posted on 2/28/13)
    Review by JIML
    Price
    Value
    Quality
    Having never painted anything before this was easy to use and my sculptures look great!
    Ground clip lasted 24 hours (Posted on 2/14/13)
    Review by Bob
    Price
    Value
    Quality
    Pure crap for a clip, and Tech Support told me just to buy myself a new one. No offer of credit or anything.

    Metal clip is as thin as paper and the pivot breaks off. In the middle of coating of course.

    All to save 5 cents.
    Works awesome but needs to be more sturdy (Posted on 10/8/12)
    Review by Lunger
    Quality
    Price
    Value
    Gun worked awesome! It was quick and easy to start coating right out of the box. The only complaint is it feels cheaply assembled. Do not tighten bottle on tight or it will break cheap! Also, it would have been nice if they would have included a fluidizer and the performance diffuser with the gun. For the price why should I have to drop another $30 for attachments for the gun to get it to run at it's best? I would have gladly paid more $ if they would have made it out of aluminum, not plastic! Yet another Chinese made item that will only last for a short while if you baby it! I'd even be happy if it was made of Kydex. All in all it should pay for itself after only a few coatings so I'm not too disappointed with the lack of craftsmanship or quality. However, if you are doing alot of coating I'd spend the extra money and get a made in the U.S.A. gun that will hold up to the demands and last!
    It is everything Eastwood claims it is. (Posted on 3/6/12)
    Review by 4x4Magnum
    Price
    Value
    Quality
    Two weeks ago I knew nothing about powder coating and now I wouldn't buy spray paint again.I've now powder coated a number of items on a custom reverse trike including the extended swingarm, a-arms, and spindles and it looks great and was really easy to do. Having the dual voltage really helps get into tight places and I'm amazed at how far 8oz of powder will go as I still haven't used all it came with. A sand blasting cabinet is a must to get the old pain off and ensure clean metal. The aluminum wheels are next. I'm confident they will look just as good. Thanks for a great product.
    Dual Voltage Powder Gun Starter Kit (Posted on 12/21/11)
    Review by David
    Quality
    Price
    Value
    This was my first time powder coating anything. This kit is pefect for a beginner. I tried reflective chrome first and I am very pleased with the results. Prep is the key, before and after pre heating. I will recommend this kit to anyone starting for the first time. Thank you Eastwood.
    awesome kit for the price (Posted on 12/8/11)
    Review by B-Ryan
    Price
    Value
    Quality
    great finish, great results would recommend this kit to anyone who wants to get started powder coating
    Excellent for a starter kit (Posted on 11/12/11)
    Review by Danno
    Quality
    Price
    Value
    This is my first try at powder coating and I went with the Eastwood dual voltage kit. Setup of the gun itself was very easy and the instructions were simple. I would recommend a beginners book on the subject. Preparation of the part to be PC is VERY important. My first project was an aluminum differential cover. I first cleaned and degrease, then media blast and then used Eastwood's chrome and clear powders. Attached are some shots of the cover.

    Would definitely recommend this product to a friend
    Excellent tool (Posted on 8/31/11)
    Review by ERIC
    Value
    Quality
    Price
    I would highly advise anyone looking to do some powder caoting to use this gun. I have done pulley's in gloss black and they are outstanding. I dropped one of the pulley's on the concrete to test it and while it did mark the surface, it did not break through the coating. I am starting to do pieces for my friends because of the way the finish looks. I have also used the blasted aluminum with great results as well. Stay with the dual voltage gun..it will come in handy!
    1st Time Powder Coater (Posted on 11/20/10)
    Review by Ryan
    Price
    Value
    Quality
    This is the first time I used a powder coating gun at all, that being said I thought this product performed flawlessly. It is much easier to powder coat parts well than to paint them. When I was powder coating some larger parts I had a little trouble getting powder into the smaller crevices so I switched the gun over to the lower voltage and the powder stuck to the part without any trouble. The dual voltage options is definetly a plus to have. The starter kit was great. But it is only a starter, I'd recommend buying more tape (although aluminum foil works great for larger areas.

    Would definetly recommend this product to a friend.

    Items 11 to 20 of 20 total

    per page
    1. 1
    2. 2

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register