Eastwood Dual Voltage Powder Gun Starter Kit

    Item #11698 Brand: Eastwood

    Quality
    Price
    Value
    18 Review(s)

    Details

    Our best value! HotCoat Powder-Coating Starter Kit includes our Dual-Voltage gun for greater versatility With our dual-voltage HotCoat powder coating gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop! Besides the dual-voltage gun, this kit also includes gloss black color, plus all the other powder coating supplies else you'll need (except compressed air and a dedicated oven) to achieve expert results.
    • Extremely durable finish
    • Coat and cure in under an hour!
    • Easy to apply
    • Quick color changes
    • Economical

    About Eastwood Dual Voltage Powder Gun Starter Kit

    Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

    One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the over-sprayed powder. Contains no environmentally harmful solvents. HotCoat Powder Coating System requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).

    (See "Contents" tab for all the specific powder coating supplies included in this Dual-Voltage kit.)


    Contents

    11676 Eastwood Dual-Voltage HotCoat Gun
    1/2-lb. Black Gloss Powder
    51558 Powder Chip Color Chart
    10078 Reusable Hi-Temp Silicone Plugs
    10027 Hi-Temp Masking Tape (1/2" x 36-yard roll)
    43045 1-lb. Stainless Steel Hanging Wire
    34066 In-Line Air Filter
    3 Empty Powder Bottles with Screw-On Tops


    Specs

    Accessories

    10041Z PRE Painting Prep
    51081 Metal Wash Metal Prep
    19418ZP Fast Etch Rust Remover and Metal Prep
    20473 2-Stage Air Dryer System
    58111 Pack of 20 Hooks
    58112 Silicone Cap & Plug Kit
    11477 Infrared Thermometer
    10590 Infrared Curing Lamp


    FAQs

    (Q) Can I use my household oven?
    (A) No, you cannot use an oven that will be used to cook/bake food.

    (Q) How long do I bake/cure the part?
    (A) 20 minutes at 400 degreesF.

    (Q) Can I remove the powder coating?
    (A) Yes, use 12849 Powder Coat & Paint Dissolver (Qt.) or 12850 Powder Coat & Paint Dissolver (Gal.) .

    (Q) How do I know what the colors will look like?
    (A) Order Eastwood's 51558 HotCoat Powder Coating Chip Chart (free in our kits).


    Safety

    Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh cartridges when curing or inspecting flow-out progress.


    Warranty

    1-year mfr's. warranty against defects.

    Designed, engineered and tested to Eastwood's specifications.

    Final product imported.


    Customers also viewed:

    Customer Reviews

    Items 1 to 10 of 18 total

    per page
    1. 1
    2. 2
    Works really well if you follow this. (Posted on 3/3/14)
    Review by Michel
    Quality
    Price
    Value
    I bought this kit for my buggy project.
    I tryed it recently, and adjusted the gun to the exacts specs, (10 psi max and about 5 cfm) if you stick to about 5 CFM you notice that the powder goes in very little cracks (as a can would do) and very low powder loss. and the result is amasingly tought.
    No more rattle cans! (Posted on 10/25/13)
    Review by K-Cat
    Price
    Value
    Quality
    I was tired of painting my “hard work” with a rattle can. I would even buy the “professional” quality spray cans, but after a while, it just wouldn’t hold up. I needed something that would hold up better. The brackets I have fabricated, truck parts, motorcycle parts, turbo compressor housing, & restoration jobs needed something more professional and durable. This gun (kit) was the next step for me. It is okay quality at a cheap price. I am very pleased with it (I didn’t expect a pro-level system). The gun is a little fragile so you have to treat it nice. With a small amount of patience, it will turn out top-notch results! Yes it’s worth it.
    Dual voltage not worth the extra money (Posted on 8/20/13)
    Review by Michael
    Value
    Quality
    Price
    I have been coating for some time using a Harbor Freight purchased system, I was not satisfied with the capability of coating crevices and recessed areas. So I purchased the Eastwood dual voltage system for the higher voltage setting to assist with this issue.

    After using the new kit I found that the higher setting did not provide any noticeable benefit over the lower setting. The coating system performed just as well as the Harbor Freight system, but at more than double the price. I feel as if the purchase was not worth the money and I would have been better off continuing the use of my Harbor Freight system or purchasing a higher end system.

    If your looking to get a powder coating system stick to the single voltage system offered by Eastwood (which my brother has and likes) here or purchase the coating system from Harbor Freight.

    Also the ground strap leaves a lot to be desired. I would recommend replacing it.
    ok but not what I expected based on reviews (Posted on 8/6/13)
    Review by Roger
    Price
    Value
    Quality
    I purchased the dual voltage powder coat gun to powder coat aluminum auto parts. It works ok but I ended up spraying more powder in my small booth than on the part to get it covered evenly. Now I per-heat my parts and I get a much better result - mainly because the powder sticks to parts with or without the electrostatic charge when they are hot.
    Gun works great (Posted on 7/30/13)
    Review by Josh
    Price
    Value
    Quality
    The gun works good, just wish the powder adheared better. I feel like 1/4 of the bottle ended up on the floor, no matter what wetting I had it on. So far the biggest thing I did was a gas tank and it came out perfect!
    Good DIY Kit for the Price!! (Posted on 6/20/13)
    Review by Mark
    Quality
    Price
    Value
    I've had a chance to use this several times now & I must say that it works very well!!

    The results are great & it's so easy to do!! I'll continue to use it for my current project as well as when I have the time & resources to finish up my long-term project!

    As for the gun itself, it would be nice to see more of a metal outer structure to it, but as long as you treat it with care & store it in a secure spot, there shouldn't be a problem with it.

    Overall, it's a value-priced powder-coating system that can give you great results if you follow the instructions & coat in a clean work environment.
    Very good start up tool (Posted on 5/8/13)
    Review by Marion
    Price
    Value
    Quality
    I was very pleased with this equipment, it was easy to set up and start using. My first powder coating experince was a good one.
    I would like for the dual voltage switch to be lighted.
    best purchase ever (Posted on 4/20/13)
    Review by Ryan
    Value
    Quality
    Price
    if you do your homework you will find this product is the best one for do it yourself guys and gals and the results are super high quality finishes that last ...normal paint was not for me... this has been on my list for my shop to purchase for a long time and as soon as I received it I put it to use and love the results ...thanks eastwood
    a great gun (Posted on 3/4/13)
    Review by bandb
    Price
    Value
    Quality
    This is a perfect unit for the beginner. It works very well and is 100% worth the amount charged. My first time powder coating went extremely well and am ready to offer this service to others wanting a great shine for a reasonable price. Thanks Eastwood for what you do. Brad in Canada
    Great addition to my shop (Posted on 2/28/13)
    Review by JIML
    Price
    Value
    Quality
    Having never painted anything before this was easy to use and my sculptures look great!

    Items 1 to 10 of 18 total

    per page
    1. 1
    2. 2

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register