Item #11973 ZP

Price
Value
Quality

4 Review(s)

Components Price: $64.98

Only $59.99

You Save $4.99

Qty:

Add to Wishlist

Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations, check with your local and state guidelines as some areas may have stricter regulations than others.

Details

2K Ceramic Underhood Black & Activator...so you only have to do it once Eastwood's 4:1 2K (2-component) Urethane Ceramic Underhood Black is the only underhood coating fortified with nano-ceramic particles to provide the ultimate in durability, chemical resistance and long-lasting good looks.

Mix 4:1 with activator included
Use your HVLP spray gun to apply
Quart is enough for about 48 square feet

Eastwood Ceramic Brake Caliper Paints

Starting at: $39.99

2 Review(s) | Add Your Review

Eastwood Self-Etch Primer Gray & Black

Starting at: $12.99

Eastwood Detail Gray Paint

Starting at: $14.99

About 2K Ceramic Underhood Black Quart Kit

Eastwood's Underhood Black is the right 10-20% semi-gloss to match that original factory sheen on firewalls, fender wells, brackets, heater boxes, pulleys and more. For maximum durability, apply over Eastwood's Epoxy Primer.

Not for sale or use in California. Eastwood Paints are formulated to meet National Rule VOC regulations; check with your local and state guidelines as some areas may have stricter regulations than others.

2K Urethane Ceramic Underhood Black, 1-quart can
Eastwood Urethane/Ceramic Activator, 8-oz. can

10041Z PRE Painting Prep
51550 Eastwood Concours HVLP Paint Spray Gun with 1.2mm tip
12817 Paint Gun Accessory Kit
50242ZP Epoxy Primer
50243ZP Epoxy Primer Catalyst
11455, 11456 SAS Bandit Respirators
51559 Digital Regulator
51483Z Rust Converter, Aerosol

To apply, mix 4:1 with the urethane activator included. (Reduction is not necessary, but can be achieved using 50104ZP Zero-VOC Urethane Paint Reducer.) Use an HVLP gun with 1.2-1.5mm nozzle size. Apply in two medium wet coats, allowing 10-15 minutes between each coat. A dry film thickness of 2 mils is recommended. Complete cure time is 24 hours. Pot life is approximately 2 hours.

Keep away from heat, sparks and open flame. Avoid prolonged contact with skin and breathing of vapors. Always wear appropriate eye, skin and respiratory protection. Consult MSDS for specific safety instructions and precautions.

Customer Reviews

Black - Nice Black! (Posted on 4/30/12) Review by Geno

Price
Value
Quality

I do like the finish - soft luster of this black. Has a soft non-gloss finish without being like a flat black that shows finger prints and grease. This "Underhood" black is one nice paint. When I lift the hood the paint accents and contrasts with out showing dust and grease on the finish.
Used HVLP out in the back yard (open air/full sun) placed parts on saw horses. I mixed it well and mixed some more, makeing sure all the pigments were in suspension as I poured to fill the gun. Heavy bottom pigments in the can - was easy to mix and use. Out in the April sun I found it best to lay down final wet coat and leave it alone to cure. Let the finish flash off uniform. You would think parts were factory new by the finish

paint gloss (Posted on 4/27/11) Review by RBE

Price
Value
Quality

Got underhood black in quart and spray can, Sprayed Engine compartment and came out gloss.Sprayed small parts with spray can and didnot match. I think I got a miss marked can. It looks ok I guess, but not what it ishould be. Called tech support and got no satisfaction.

proper sheen (Posted on 1/9/10) Review by reynolds

Price
Value
Quality

I searched for that proper sheen of black for my 66 mustang, I was concerned about doing all of that media blasting to make it perfect, and then getting a paint that did not match the proper sheen on my 66 mustang. Well I must say that this paint is perfect. It looks awesome, and applied over their epoxy primer, it seems to be cured very well and it seems very durable. Just remember to let the paint cure for about 5 days because the epoxy takes time to cure especially in colder weather, I am very happy with the results.

GOOD PRODUCT (Posted on 12/12/09) Review by JIM

Quality
Price
Value

I WAS VERY PLEASED WITH THE RESULTS AND EASE OF MIXING AND APPLICATION. AT FIRST I THOUGHT NO WAY WAS THERE ENOUGH TO DO THE JOB BUT THE HVLP GUN SET AT THE RIGHT PRESSURE FOOLED ME! I WAS ABLE TO DO THE WHOLE FRAME ON MY 49" CHEVY PICKUP, THE INNER FENDERWELLS, FRONT AND REAR AXLES AND MUCH MORE. I WAS GLAD TO HAVE THE SPRAY CAN FOR TOUCHUP AND IT MATCHED PERFECTLY. WHEN THE PAINT DRIED IT WAS HARD TO SCRATCH AND LOOKED GOOD!