Dual Voltage HotCoat Powder Coat Elite Kit

    Item #12450


    "Elite" Dual-Voltage HotCoat Kit comes with everything for powder-coating, including 4 standard colors of your choice, and gloss black With our dual-voltage HotCoat powder coating gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Kit has everything you'll need (except compressed air and a dedicated oven) to achieve the benefits of powder coating and expert results.
    • Includes your choice of 4 standard colors, plus black
    • Extremely durable finish
    • Coat and cure in under an hour!
    • Easy to apply
    • Quick color changes
    • Economical

    About Dual Voltage HotCoat Powder Coat Elite Kit

    This elite kit includes one of the market's best powder coating spray guns. Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. Plus, thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.

    One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat Powder Coating System requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven).

    (See "Contents" tab for all the specific items included in this Dual-Voltage "Elite" kit.)


    11676 Eastwood Dual-Voltage HotCoat Gun
    1/2-lb. Black Gloss Powder
    51558 Powder Chip Color Chart
    10078 Reusable Hi-Temp Silicone Plugs
    10027 Hi-Temp Masking Tape (1/2" x 36-yard roll)
    43045 1-lb. Stainless Steel Hanging Wire
    34066 In-Line Air Filter
    3 Empty Powder Bottles with screw-on tops
    Beginning Powder Coater's Handbook


    10041Z PRE Painting Prep
    51081 Metal Wash Metal Prep
    19418ZP Fast Etch Rust Remover and Metal Prep
    20473 2-Stage Air Dryer System
    58111 Pack of 20 Hooks
    58112 Silicone Cap & Plug Kit
    11477 Infrared Thermometer
    10590 Infrared Curing Lamp
    10255 Hotcoat Powder High-Tech Color Sample Kit
    10421 High-Temp Masking Tape Kit


    (Q) Can I use my household oven?
    (A) No, you cannot use an oven that will be used to cook/bake food.

    (Q) How long do I bake/cure the part?
    (A) 20 minutes at 400 degreesF.

    (Q) Can I remove the powder coating?
    (A) Yes, use 12849 Powder Coat & Paint Dissolver (Qt.) or 12850 Powder Coat & Paint Dissolver (Gal.) .

    (Q) How do I know what the colors will look like?
    (A) Order our 51558 HotCoat Powder Coating Chip Chart (free in our kits).


    Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh cartridges when curing or inspecting flow-out progress.

    Customers also viewed:

    Customer Reviews

    7 Item(s)

    per page
    Satisfied However! (Posted on 3/16/2013)
    Review by Antdog
    Great web page experience and prompt delivery... Good price for the value... However, my ground clamp hinge broke on the third day making equipment useless.. I repaired with a heavier duty clip and now even better. Highly Recomended for DIY.
    Good gun, books worthless! (Posted on 4/30/2012)
    Review by K.V.T.
    So far gun is a plus. School of trial and error is better than book. Defusser that comes with kit does not fit emmitter rod and falls off. Eastwoods solution was to hit it with a hammer to close up hole that is too big. Kind of expected more help or a replacement part for my $260.00. Gun 1.......... Eastwood 0
    Not to happy so far (Posted on 4/23/2012)
    Review by CAL
    I received gun and products and once everything was set up in the shop and ready to go I find out there is no power to the gun at all. Also, powder leaked out of the top of the powder cup once air was applied. Called tech support and find out the gun needs to be replaced (right out of the box). Was there any quality control or testing at all done before it was sold to me ?? I have heard great reviews and poor reviews both about this product.

    So I sent the gun back and it has been 13 days since they have even thought about sending a replacement. Called customer service (on Monday) and she says it will be handled at the end of the week. In my opinion this was terrible customer service. I have loved other Eastwood products in the past but this just feel this was a bad deal so far. Hope im proven wrong once the gun arrives and I start coating...
    First pc gun, works fine (Posted on 3/19/2012)
    Review by Thumper
    Shipping to B.C. Canada takes 19-26 days, not Eastwood's fault.
    I find that I need to bake the first coat, then bring item out & give second coat hot & re bake to get better desirable finish, one coat looks to thin.It is a neat way to paint.Time will tell on durability. Powder comes out the side of my gun also, will have to see if I can remedy problem at connection of lid to shooting barrel.I sand blast every thing first, every thing must be clean & wiped with Pre or acetone.
    Works Great! (Posted on 1/19/2012)
    Review by GPE
    Fast shipping, came a couple days later. I started powdercoating that day. Everything works great! Only problem I had was powder blowing out the side of the gun where the bottle connects. I pulled the long tube off put an o ring on it and now it's fine. Overall you wont be dissapointed. Eastwood is great!
    first time powder coating and it works great (Posted on 1/15/2012)
    Review by kneedown4GOD
    i bought this kit just to do atv and motorcycle parts and a few car parts as well.it is easy to use and actually turned out a better result than i was expecting.the eastwood powder is tough and shines awesome.
    this is my first time i ever powder coated and love it (Posted on 3/5/2011)
    Review by vlad
    i bought this kit to powder coat dirt bike parts and for being my firt time, well i think it turned out great this really is a great gun would recommend to other.

    7 Item(s)

    per page

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register