- Eastwood Rust Encapsulator - Paint Over Rust in Black
Eastwood Rust Encapsulator - Paint Over Rust in Black
Item #Encapsulator 16060
You thought it was good before...wait ’til you try this Rust Encapsulator! It seals and stops rust and corrosion from spreading, but it performs even better than our original formula. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability.
- Twice the corrosion resistance of our original formula for greater durability (tested to 500 hours in a salt-spray chamber)
- Epoxy-fortified for better adhesion and topcoat compatibility
- Penetrates deeper to prevent rust from spreading or forming, even in hard-to-reach areas
- Cures faster, and the low-VOC formula is acceptable in California
- 15-oz. aerosol covers about 10 sq. ft.
- As seen on "My Classic Car" TV show
About Eastwood Rust Encapsulator - Paint Over Rust in Black
Eastwood Rust Encapsulator has been tested by an independent lab to be one of the most effective rust-preventive products yet. Rust Encapsulator is a great primer for floor pans and other underbody parts. It fills tiny pin-holes and surface irregularities, and is compatible with lacquer, enamel and urethane topcoats (including Eastwood Chassis Black). For the absolute ultimate rust remedy, first brush or spray-on Eastwood Rust Converter, then prime with Rust Encapsulator. One 15-oz. aerosol covers about 10 sq. ft., and contains no isocyanates. Heat-resistant up to 400°F. Made in the USA.
Use a wire brush to remove loose rust, scale and paint, and remove dust, grease and oil deposits. Wipe down with either Acetone or Pre Painting Prep (10041Z). Feather surrounding paint with 220-grit sandpaper. Shake can for at least 2 minutes once the mixing ball starts to rattle. Hold the Rust Encapsulator can 10-12" above surface as you spray. A single coat dries to the touch in 20 minutes, and is thoroughly dry in 3-4 hours at 68°F. For greater durability, a second coat can be applied 1 hour after the first. Allow 6-8 hours after the last coat before applying topcoat. Use over or under body fillers.
Choose from the following:
14761Z is the Trial-Size Rust Encapsulator, Black, 2-oz. Aerosol
16060Z is the Rust Encapsulator, Black, 15-oz. Aerosol
26060Z is the Rust Encapsulator with Extension Nozzle, Black, 15-oz. Aerosol
16065ZP is the Rust Encapsulator, Black, 1-quart Can
16070ZP is the Rust Encapsulator, Black, 1-gallon Can
Quart can is also available in a 12-pack
(Q) Can Rust Encapsulator be applied with the Undercoating System?
(A) Technically, yes, but this application isn't recommended because Rust Encapsulator requires surface to be free of grease, oil, and loose rust. The best product to coat inside box sections is the Heavy-Duty Anti-Rust (16017ZP). This waxy, oily product flows into pinch welds and through rust to seal surfaces from contact with moisture and air, but cannot be painted over, so it's only suitable for inside box sections that don't show. Use lacquer thinner for cleanup.
Work in a well-ventilated area when applying this product. The use of a respirator is recommended. Shake vigorously for 2 minutes before spraying.
In places where little or no surface prep can be done, our Heavy-Duty Anti-Rust (16017ZP) is actually a better choice for applying into blind areas such as box sections.
Customers also viewed:
High-grade patina preserving coat prevents further discoloration and protects surfaces from corrosion
Stops rust, and protects the underside of your car!
Starting at: $19.99
Transforms surface rust into a paintable surface!
Starting at: $19.99
Encapsulates rust and prevents spreading; leave as is, or top-coatOnly $54.99
Stop rust in its tracks, then seal cracks, crevices and body seamsOnly $54.99