- Rust Encapsulator Clear Matte 15 ounce Aerosol
Rust Encapsulator Clear Matte 15 ounce Aerosol
You thought it was good before...wait ’til you try this Rust Encapsulator! It seals and stops rust and corrosion from spreading, but it performs even better than our original formula. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability.
- Near invisible clear matte finish protects and preserves bare metal surfaces
- Apply over painted surfaces that you do not want to alter the color
- UV resistant and can be used as a top coat
- Preserves rust and patina to keep that barn find look
- Durability tested to 500 hours in a salt-spray chamber
- Epoxy-fortified for better adhesion and topcoat compatibility
- Penetrates deeper to prevent rust from spreading or forming, even in hard-to-reach areas
- Cures faster, and the low-VOC formula is acceptable in California
- 15-oz. aerosol covers about 10 sq. ft.
- As seen on "My Classic Car"; TV show
Due to regulations pertaining to recycling, we are unable to ship this product to Alberta, Canada.
About Rust Encapsulator Clear Matte 15 ounce Aerosol
Eastwood's Rust Encapsulator has been tested by an independent lab to be one of the most effective rust-preventive products yet. Clear Rust Encapsulator has a near invisible matte finish that protects and preserves bare metal surfaces and can be used as a UV resistant top coat. It fills tiny pin-holes and surface irregularities, and is compatible with lacquer, enamel and urethane topcoats (including Eastwood Chassis Black). Apply over painted surfaces that you do not want to alter the color or to preserve the rust and patina to keep that barn-find look. One 15-oz. aerosol covers about 10 sq. ft., and contains no isocyanates. Heat-resistant up to 400°F. Made in the USA.
Net Weight 15 ounces
10041Z PRE Painting Prep, 13651Z Rubberized Rust Encapsulator, 12515Z internal Frame Coating, 12096 Gel Rust Dissolver, 51483Z Rust Converter,
Use a wire brush to remove loose rust, scale and paint, and remove dust, grease and oil deposits. Feather surrounding paint with 220-grit sandpaper. Shake can for at least 2 minutes once the mixing ball starts to rattle. Hold the Rust Encapsulator can 10-12" above surface as you spray. A single coat dries to the touch in 20 minutes, and is thoroughly dry in 3-4 hours at 68 deg F. For greater durability, a second coat can be applied 1 hour after the first. Allow 6-8 hours after the last coat before applying topcoat. Use over or under body fillers.
always wear eye, skin and respirtaory protection. Apply in a well ventilated area away from open flame.
Made in USA
Wire Brush to remove loose rust, scale and paint. Remove dust, grease, oil deposits. Shake can for at least 2 mins after mixing ball starts to rattle.Feather surrounding paint with 220 grit sandpaper. Apply Rust Encapsulatorcan 10 to 12 inches from surface. Single coats dry to the touch in 20 minutes and arethoroughly dry in 3 to 4 hours at 68 degrees F. For greater durability a second coat can be applied one hour after the first. Allow 6 to 8 hours after last coat before applying top coat.
Customers also viewed:
High-grade patina preserving coat prevents further discoloration and protects surfaces from corrosionOnly $19.99
Stop rust in its tracks!
Starting at: $4.99
Stops rust, and protects the underside of your car!
Starting at: $17.69
Transforms surface rust into a paintable surface!
Starting at: $15.49
Stop rust in its tracks, then seal cracks, crevices and body seamsOnly $54.99