• Home
  • Rust Encapsulator Safety Yellow 15 ounce Aerosol
Rust Encapsulator Safety Yellow 15 ounce Aerosol is rated 3.5 out of 5 by 4.
Rated 5 out of 5 by from product works well spraying rust encapsulator between layers of metal we are replacing in rockers of 60 impala, really to cold by rites but it is covering good and doing its thing.
Date published: 2015-01-10
Rated 1 out of 5 by from On sale for a reason I bought this to paint a transmission cross member and second transmission cradle. They are from a Subaru so not large parts. These parts are formed/boxed so all the exterior was sand blasted as was as much of the inside I could get at. Then parts were soaked in Evapo-Rust, thoroughly rinsed with water/mild degreaser and then wiped with Acetone to remove anything the water/degreaser didn't get. Evapo-Rust requires a water rinse if you are wondering why I went that route. Regardless, the metal was clean and had a good profile. I found this paint did not cover well, and was very slow to dry at 60 degrees. After 24 hours the paint was soft and I could wiped it to bare metal with Acetone and a rag. I scuffed the Rust Encapsulator as directed after 24 hours to topcoat. I felt like i was removing my kids paint from the kitchen table. I top coated with Rustoleum and am expecting these parts will need paint again in a couple years due to the poor adhesion of this product. If you are wondering I painted the inside of my parts using Eastwoods 24 inch aerosol wand which works well.
Date published: 2015-02-26
Rated 4 out of 5 by from coverage not as good I have purchased the black and red for years but the yellow was on sale so I tried it. Long term I will have to see how it performs but I felt it did not cover as well as the black and red
Date published: 2015-02-17
Rated 4 out of 5 by from unsure just applied and it covers well, as far as how well it works will take some time.
Date published: 2015-02-10
  • 2015-04-20T09:21CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_4
  • loc_en_US, sid_14821Z, PRD, sort_relevancy
  • clientName_eastwood

Is this paintable?

Asked by: royc
Yes, you can prime and paint over top of this product
Answered by: SeanA
Date published: 2014-11-25
  • 2015-04-20T10:31CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_US, sid_14821Z, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Rust Encapsulator Safety Yellow 15 ounce Aerosol

Item #14821Z Brand: Eastwood

Reformulated with TWICE the corrosion resistance!

Details

Stop rust in its tracks! Our Rust Encapsulator (Safety Yellow) has been reformulated with TWICE the corrosion resistance!

You thought it was good before...wait ’til you try this Rust Encapsulator! It seals and stops rust and corrosion from spreading, but it performs even better than our original formula. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability.

  • Safety Yellow
  • Twice the corrosion resistance of our original formula for greater durability (tested to 500 hours in a salt-spray chamber)
  • Epoxy-fortified for better adhesion and topcoat compatibility
  • Penetrates deeper to prevent rust from spreading or forming, even in hard-to-reach areas
  • Cures faster, and the low-VOC formula is acceptable in California
  • 15-oz. aerosol covers about 10 sq. ft.
  • As seen on "My Classic Car" TV show


  • Due to regulations pertaining to recycling, we are unable to ship this product to Alberta, Canada.

More info...

About Rust Encapsulator Safety Yellow 15 ounce Aerosol

Eastwood Rust Encapsulator has been tested by an independent lab to be the most effective rust preventive product yet. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability. One 15 oz. net wt. aerosol covers about 10 sq. ft. Contains no isocyanates. Heat resistant up to 400³ F.


Contents

Net Weight 15 ounces


Accessories

10041Z PRE Painting Prep, 13651Z Rubberized Rust Encapsulator, 12515Z internal Frame Coating, 12096 Gel Rust Dissolver, 51483Z Rust Converter,


Application

Use a wire brush to remove loose rust, scale and paint, and remove dust, grease and oil deposits. Feather surrounding paint with 220-grit sandpaper. Shake can for at least 2 minutes once the mixing ball starts to rattle. Hold the Rust Encapsulator can 10-12" above surface as you spray. A single coat dries to the touch in 20 minutes, and is thoroughly dry in 3-4 hours at 68°F. For greater durability, a second coat can be applied 1 hour after the first. Allow 6-8 hours after the last coat before applying topcoat. Use over or under body fillers.


Safety

always wear eye, skin and respirtaory protection. Apply in a well ventilated area away from open flame.


Warranty

Made in USA


Application

Wire Brush to remove loose rust, scale and paint. Remove dust, grease, oil deposits. Shake can for at least 2 mins after mixing ball starts to rattle.Feather surrounding paint with 220 grit sandpaper. Apply Rust Encapsulatorcan 10 to 12 inches from surface. Single coats dry to the touch in 20 minutes and arethoroughly dry in 3 to 4 hours at 68 degrees F. For greater durability a second coat can be applied one hour after the first. Allow 6 to 8 hours after last coat before applying top coat.


Customers also viewed: