• Home
  • Eastwood Stitch Weld Magnets
Eastwood Stitch Weld Magnets is rated 4.5 out of 5 by 21.
Rated 5 out of 5 by from They may be small, but they are mighty I haven't used them for their intended purpose yet, but I have used them to aid in placement and aligning of weld-in louvers on my car's hood, and two of them can hold an 18 x 7 piece of 20 gage steel without so much as a whimper. Couple of things to be wary of. They state in the directions that they are brittle and will chip if allowed to come together with any force. They aren't kidding. I wasn't careful and allowed two to get too close to each other and they snapped together with enough force to chip one. Also, keep them in the box when you are not using them. I left one out on the bench while I did some fine tuning with a grinder, and it collected every metal filing within a foot. I now have a magnetic Chia Pet covered in metal chips and they are a bugger to remove. If you follow the instructions, store them carefully and use as intended, they are a great product.
Date published: 2015-12-20
Rated 4 out of 5 by from Strong little magnets. I bought a package of magnets three weeks ago. When I opened them I was surprised on how strong they are. In showing my daughter some of them snapped together and a couple of them chipped. That was disappointing. If thinking of product improvement, think of some kind of covering that would prevent chipping. Otherwise, these are strong enough to hold any panel in place until it is welded. I am happy that I bought them and will probably buy more for larger panels.
Date published: 2016-05-10
Rated 5 out of 5 by from Many Many Uses I bought 2 sets of these a month ago they are the best magnets I have ever used, I run the fabrication department in a very large restoration shop and everybody wants to borrow them all the time! I have used them for so many different jobs, I'm going to buy a couple more sets just to have more on hand and the price is GREAT.
Date published: 2015-12-23
  • y_2017, m_8, d_18, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_21
  • loc_en_US, sid_20421, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

Do these magnets come in some sort of protective case?

Asked by: dan0
These are shipped in a cardboard box with dividers between them.
Answered by: S Church
Date published: 2016-12-30

Hey Guys, Heat is the enemy of these magnets.  It destroys the magnetic capability.  Are these magnets any different?

Asked by: njmj
These magnets are designed to be considered a consumable and will eventually wear out. They are very strong though and will hold up for quite some time.
Answered by: S Church
Date published: 2017-06-15
  • y_2017, m_8, d_18, h_4CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_20421, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood Stitch Weld Magnets

Item #20421

Super strong magnets hold patch panels in place, perfect for blind repairs

In stock

Only $19.99

Sale $17.97

Details

Super strong magnets hold patch panels in place from the outside, perfect for blind repairs.

  • 8 pack of strong rare earth magnets
  • 1/2 inch (12.7mm) diameter disc
  • Strong enough to hold patch panels
  • Hold flush patches in perfect alignment
  • Position panels with no gaps
  • Perfect for blind repairs

If you have ever tried to weld a patch panel into a spot where you can’t access the back side, these rare earth magnets are a life saver. These nickel plated super strong magnets come 8 to a package, and each one measures just 1/2 inch (12.7mm) in diameter, but are strong enough to support several pounds. Place them every few inches at the edge of your panels and you can position the panel with no gap, or the perfect gap for whichever welding method you are using. Use a few of these magnets and never feel like you need 3 hands again.

These 12.7mm diameter x 19mm length rare earth neodymium nickel plated magnets are design to offer superior panel alignment when welding patch panels. With N35 strength, high heat resistant of up to 200F, these magnets will keep both panels in perfect alignment when stitch welding. 8 pieces are included in this kit in which are used approximately 2 inches apart along your weld seem. The magnets will keep both panels level and aligned, while eliminating panel gaps, distortion and raised/recessed areas. For use when MIG, TIG or Gas welding to hold panels while tack welding material.


More info...

Contents

12.7mm diamter x 19mm length, 8 N35 strength Neodymium rare earth magnets


Safety

Magnets are nickle plated to eliminate corrosion. In use the nickle plate may chip and the magnets may need to be replaced after time.


Warranty

1 Year Warranty


Customer Reviews

Questions & Answers

Customers also viewed: