• Home
  • Versa Cut 40 & 60 Plasma Cutters Air Diffusers
Versa Cut 40 & 60 Plasma Cutters Air Diffusers is rated 2.3333 out of 5 by 12.
Rated 3 out of 5 by from over-priced. My versa 60 cuts 3/8" 1018 steel like it was butter. So long as you have a good standoff, and a steady hand, all is fine.... but, the wore standoff that comes with the Versa 60 is near useless and you will soon find yourself shorting it out, burning the ends off... then, everything is at risk. A homemade standoff I have works far better, and has greatly reduced the failures of the nozzle, diffuser, cap end and electrodes. If you have a lathe, make one out of s short piece of metal tube steel, with a set-screw, and 2 or 3 legs..
Date published: 2013-09-07
Rated 2 out of 5 by from Too expensive for a consumable like this! The Versa 60 cuts 1/4" steel like butter, and leaves a nice clean cut (if set correctly). The problem is, it is very easy to err in the first settings of a new project -- and just one mistake, where air pressure drops suddenly during a cut... and bing badda bang, you'll have melted the electrode, diffuser and the contact cap, faster than Superman leacrushing a flimsy Coke can.. These diffusers should be sold for this price in a bag of TEN!
Date published: 2013-01-31
Rated 4 out of 5 by from Diffuser I have used several other major brands of plasma cutters in heavy fabrication shops. All have good and bad points. I choose this tool from this company for price and quality of tool and consumables. Any plasma cutter will fail if not used correctly. Think eastwood has done good job offering package of quality and price for the average guy or small business like me to be able to get a tool that would cost two to three times in a name brand.
Date published: 2014-12-03
Rated 2 out of 5 by from Melts frequently Yes my technique on plasma cutting needs work so I can't lay all of the blame with this product. I will say when you cut thick metal or start in the middle of the metal cutting, watch out because hot metal tends to make its way into the nozzle and melt these consumables. A slightly lower price would make these a little more palatable. After going through 3 of these my cost of ownership is going up quickly.
Date published: 2014-11-20
Rated 1 out of 5 by from Plasma Versa 60 Air Diffuser I followed all directions to the T and then I forgot to turn on my air supply the very first time I used the Versa 60, instantly fried the Air Diffuser. A simple mistake on a first run will always get your attention from there on after. I would like to see these in bags of 5 or 10 for the same price as an individual.
Date published: 2013-03-25
Rated 1 out of 5 by from Way too fragile! This part is way too fragile for the price. Easy to burn one of these out if you forget your air, so to pay these prices for such a disposable item is very out of line. Love my plasma cutter, but cannot believe the cost for this part.
Date published: 2015-03-09
Rated 1 out of 5 by from too high price too expensive for something so easy to ruin during the learning curve- no graduations on amperage setting so it's "trial & error"
Date published: 2012-12-06
Rated 3 out of 5 by from versa cut 60 air diffuser Dont forget to turn on the air compressor like I did>>>>>Or you will be buying a lot of these.....Beside that great machine....
Date published: 2015-01-04
  • 2015-03-29T09:58CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_12
  • loc_en_US, sid_13788, PRD, sort_relevancy
  • clientName_eastwood

Versa Cut 40 & 60 Plasma Cutters Air Diffusers

Item #13788 Brand: Eastwood

Replacement air diffuser for Eastwood's Versa-Cut 40 & 60 Plasma Cutters

Details

These are a set of two replacement Air Diffusers for Eastwood's Versa Cut40 & 60 Plasma Cutters. This is the piece that goes between the nozzle and electrode and after time will need to be replaced. Includes 2 pieces.

More info...

About Versa Cut 40 & 60 Plasma Cutters Air Diffusers

This is a replacement Air Diffuser for Eastwood's Versa Cut 40 & 60 Plasma Cutters.This is the piece that goes between the nozzle and electrode and after time will need to be replaced. Includes 2 pieces.


Contents

Includes: 2 Replacement Air Diffusers.


Application

This is a replacement Air Diffuser for Eastwood's Versa Cut40 & 60 Plasma Cutters.This is the brown plastic piece that is located in the torch of the plasma cutter which separates the nozzle and electrode.


Customers also viewed: