• Home
  • Eastwood 25 Ft Welder Extension Cord
Eastwood Welder Extension Cord 25 Ft is rated 5.0 out of 5 by 14.
Rated 5 out of 5 by from Works great for Millermatic 211 Auto-Set with MVP! I have been looking for a well-built extension cord for my Millermatic 211 Auto-Set with MVP. I bought the 25' version of this cord and could not be happier. My garage only has (1) 230V outlet and I have that outlet wired for a NEMA 6-50R receptacle that fits the Miller MVP plug, so without an extension cord I am limited to welding on one side of my garage only. With this cord I can finally reach projects on the other side of my 3-car garage and out into the driveway. I did not notice any reduction in welding ability (no noticeable drop in voltage). Great quality and value!
Date published: 2015-03-09
Rated 5 out of 5 by from handy was looking for an extension for general use around the shop. works well on both my welder & plasma cutter
Date published: 2014-06-19
Rated 5 out of 5 by from Heavy Dury Very nice, heavy duty drop cord. Well worth the money. Used it right away, worked great. Should last for years
Date published: 2014-10-24
Rated 5 out of 5 by from A must have for a welder or plasma cutter I purchased a welder / plasma cutter and then realized I needed more cord. This thing is AWESOME!
Date published: 2014-11-03
Rated 5 out of 5 by from HARD TO FIND Bought me a little MIG welder and I only have one 220 outlet in my shop. Well, my car is on the other side of the shop on blocks. I searched for the raw parts to make one of these extension cords myself, then stumbled on this. Lower cost than doing it myself, and much higher quality. Works great! Should be an automatic add on accessory for every welder.
Date published: 2015-04-17
Rated 5 out of 5 by from better then I expected I could not believe the product. I was hesitant to spend the money. But it sure best my hand made extension cord I had used for years. Very well made and heavy duty but very easy to use and not stiff. Plus into both of my plasma cutters welder and compressor.
Date published: 2015-04-11
Rated 5 out of 5 by from Welder Extension Cords I bought two welder extension cords about a month ago. I was pleasantly surprised with their quality. These cords are extremely heavy duty and of the highest quality. After seeing what quality they are I ordered four of them for a job I have going at work.
Date published: 2015-03-25
Rated 5 out of 5 by from Well made welder extension cord I just bought this welder cord and I haven't had a chance to use it, yet, but it seems to be well made and the price was right for it. I am very satisfied with the purchase and I service was fantastic.
Date published: 2015-01-10
  • 2015-04-23T09:26CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_14
  • loc_en_US, sid_20029, PRD, sort_relevancy
  • clientName_eastwood

Will the circuits in a 220v clothes dryer outlet work as a power source (after changing the connector)?

Asked by: Goatbiker
It depends, most dryer outlets are 30 amp.  If the equipment your operating is rated at 30 amps you're OK. 
Answered by: RickN
Date published: 2015-01-05

Is this for 110 or 220 circuits?

Asked by: phordphan77
It is for 220v
Answered by: SeanA
Date published: 2014-11-22

Are the Cords approved by MSHA?

Asked by: Morrowfied
  • 2015-04-23T09:21CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_3
  • loc_en_US, sid_20029, PRD, sort_recentAnswersFirst
  • clientName_eastwood

Eastwood 25 Ft Welder Extension Cord

Item #20029 Brand: Eastwood

Perfect welding extension cord that meets all industry and customer standards.


The Eastwood Welding Extension Cord is what you need when you have to take your welder to the project. The 25ft, 6 AWG, 3 conductor UL listed cord has an industry standard NEMA 6-50 Plug and Receptacle, which are what you need for 50 amp circuits. The copper is electrical grade so there’s only a minimal voltage drop to your machine. The cord has abrasion-resistant, heavy insulation to protect the wiring. Finally, an extension cord strong enough to use for welding and long enough to actually be useful.

More info...

About Eastwood 25 Ft Welder Extension Cord

The Eastwood Welding Extension Cord is 25ft long – long enough to bring your welding machine to your project, not the other way around.


25 ft industry standard NEMA 6-50 plug and receptacle. 3 conductor 6AWG cord with UL listed cable and plug/receptacle.


Do not allow water or moisture to contact plug or receptacle when using cord.


365 days warranty. Imported


Use with Mig175(12012), Versa Cut 40(12740), Versa Cut 60(14099), Tig200AC/DC(12746) and the Tig200DC (14100) to greatly extend range. No longer do you have to bring the project to the welder. Also works with other brand welders that use a NEMA 6-50 plug.

Customers also viewed: