FREE Lifetime Tech Support
We're here to help you Do The Job Right.
This product includes FREE Lifetime Tech Support from our U.S.-Based Customer Solutions Team.
Looking for advice on your project or product recommendations? Our in-house Project Advisors have the same passion for DIY automotive restoration as you do. Get advice on your project, personalized product recommendations and answers to your questions. Give us a call or email projectadvisors@eastwood.com.
Eastwood's 2K Aerospray High Build Urethane Primer Aerosol allows you to paint with the durability and precision of a two-component coating without the paint gun! Formulated with Eastwood's proprietary technology to provide a long-lasting and durable finish, while keeping its beautiful finish for years.
2-Component Catalyzed Technology
Two Chamber Design Aerosol
Most Durable Aerosol Urethane Primer Available
Sprays Like a Paint Gun
The innovative nozzle and valve technology, combined with its two internal chambers, ensure the right ratio is mixed every time. Sprays like a gun with a broader spray pattern than conventional aerosols, and no mess to clean up. You'll achieve professional results from an easy-to-use aerosol.
What's Included
11.8 ounces net weight
Safety Information
Always wear eye, skin and respiratory protection when using this product.Product contains Isocyanates, wear NIOSH approved breathing equipment. Always use in a well ventilated area away from open flame. Consult MSDS for specific safety warnings
Before activating, shake aerosol vigorously for 1 min. Take red button from cap. Rotate aerosol 180 degrees and attach button to pin on aerosol bottom. Place aerosol on firm ground upside down. Press red button with the ball of your hand until stop is reached.After activating, shake aerosol again vigorously for 2 min. Pot life 48 hours at 68 degreesF.
Rated 5 out of
5 by
Ulysses D from
Great ProductGreat primer, I used it on the barrels of my rims. Need a high temp product that cures chemically. Next was the 2k High Temp red paint. Wow....
Date published: 2023-11-16
Rated 5 out of
5 by
Dave C from
Good stuff!Great product - I used this product to prime a motorcycle that I re-painted and had results comparable to using an air gun. Highly recommend.
Date published: 2023-11-14
Rated 5 out of
5 by
Joe G from
2 k primer greyGreat product sprays great like a gun and sands well
Date published: 2023-06-29
Rated 5 out of
5 by
heppcat from
201941 buildworked very well, no surprises. happy with my purchase.
Date published: 2022-11-15
Rated 5 out of
5 by
69 Corvair from
Easy to use nice spray patternGreat product. Used to get to those areas that were hard to roll and to touch up the primer after my final sanding. After applying I hit it lightly with the very fine ScotchBrite pad and it was ready for paint.
Date published: 2022-08-08
Rated 5 out of
5 by
Mike from
good stuffgoes on like out of a spray gun. ends up nice and smooth.
In ideal temps- it's only a 5-7 minute flash period in between coats.
Answered by: Kelly H
Date published: 2023-12-20
Can this be used on a door that has electro-deposit primer (EDP) on it?
Asked by: Liam1024
YES, Scuffing with sandpaper or a scuff pad is all that is required Then pre-paint prep to clean the surface of your replacement panels for better primer/paint adherence.
Answered by: Anonymous
Date published: 2023-09-14
Can this be applied over a polyurethane based sealant?
Asked by: Revo2814
Yes
Answered by: Anonymous
Date published: 2023-09-14
Can this be sprayed along with 2k primer surfacer?
Asked by: Camaroman
This is the 2K Primer surfacer. This and the gallon kits can be used over one another without issues.
Answered by: Kelly H
Date published: 2022-08-22
If I spray your epoxy Gray primer can I clearcoat over it? And what grit of sandpaper should I use on the primer before clearcoating?
Asked by: Arnold
Technically yes you can. You would want to sand with 600-800 grit before applying clear.
Answered by: Kelly H
Date published: 2023-06-01
Is this 2K Primer compatible with U-Pol Etch Primer
Asked by: Mikey
Unfortunately, we can not guarantee compatibility between our products and brands we do not sell. We would have to advise you to test a small area first before applying liberally over the entire surface.
Answered by: Kelly H
Date published: 2021-11-19
Does this product work on fiberglass
Asked by: Jerry
This will have no issues going over the top of properly prepped fiberglass.
Answered by: ZachC
Date published: 2021-11-19
Can I spray this directly to Fiberglass (epoxy resin)?
Or should I spray a epoxy primer first? Weight is important in this case.
Asked by: Oliver
Since there will be no bare metal you can skip the epoxy and go right to this primer over properly prepped fiberglass.