National Commitment Day
  • Home
  • Eastwood Bonneville Black Cherry Pearl 3:1 Single Stage Paint

Eastwood Bonneville Black Cherry Pearl 3:1 Single Stage Paint

Eastwood Bonneville Black Cherry Pearl 3:1 Single Stage Paint

Item #50280ZP Bonneville Black Cherry Pearl

Sophisticated color is deep and dark with beautiful shades of red and a subtle sparkle.
  1. Quantity:
    Quantity: close
    EW Bonneville Black Cherry Pearl Paint 96 OZ
    Item #50280ZP
    Only $85.99

    In stock

  2. Quantity:
    Quantity: close
    Eastwood Medium Speed Activator for Single Stage Paints 32 oz 70 to 80 Degrees F
    Item #21856ZP
    Only $26.99

    In stock

  3. Quantity:
    Quantity: close
    Eastwood Single Stage Urethane Slow Activator 80 Degrees F and above Mix 3:1
    Item #21853ZP
    Only $28.99

    In stock

  4. Quantity:
    Quantity: close
    Eastwood Zero VOC Urethane Reducer Quart
    Item #50104ZP
    Only $17.99

    In stock




< Back


Eastwood Bonneville Black Cherry Pearl - This sophisticated color is deep and dark with beautiful shades of red and a subtle sparkle.

Eastwood's premium Single-Stage Acrylic Urethane Topcoat provides exceptional long-lasting beauty and durability.

  • Catalyzed urethane for unsurpassed durability
  • Highly resistant to UV rays, chemicals, chips
  • Makes 1 sprayable gallon when mixed 3:1 with a required activator
  • Approximate coverage: 125 SQ FT
  • Flake/Pearl Particle size: 10-60 microns
  • Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
  • Made in the USA

This premium 2-component topcoat system is blended with top-quality raw materials and advanced composition coatings technology. Superior to acrylic, alkyd and lacquer coatings. Eastwood's single-stage urethane paints hold their gloss longer and won't yellow.

More info...
< Back


Thoroughly mix three parts single-stage urethane paint with one part Activator. No additional reduction is required but can be used as needed. Use caution in mixing materials as Eastwood’s single-stage urethane paint may begin to gel after approximately two hours (at 70 °F).

HVLP Gun: Fluid Tip 1.3-1.5 mm Inlet Spray Pressure 25-30 psi
Conventional Gravity: Fluid Tip 1.3-1.6 mm Inlet Spray Pressure 45-50 psi
Conventional Siphon: Fluid Tip: 1.4-1.8 mm Inlet Spray Pressure 45-50 psi

Apply single-stage urethane paints in two to three medium wet coats as necessary to achieve sufficient coverage, allowing ten minute flash between coats. Additional coats may be necessary to achieve total coverage for some metallic colors. A final “fog coat” may be applied with metallic colors to help set an even flake pattern and /or adjust flake orientation. A dry film thickness of approximately 2 mil is recommended. Paint should be dust free within 10-15 minutes and tack-free within one hour (at 70 °F). Re-coat anytime after the previous coat has flashed, or before 18 hours. After 18 hours, paint should be abraded prior to re-coating for proper adhesion purposes.

This urethane paint may be applied as a stand-alone single-stage system, or in combination with Eastwood’s High Solids Urethane Clear as a basecoat/clearcoat system. Additionally, Urethane Clear may be integrated into Urethane color. When combining the two systems, be sure to activate each side (the paint and the clear) separately, with their own activators at the correct mix ratios, before blending.

When used as a Single-Stage Urethane Paint, this coating may be wet-sanded and polished for increased depth and gloss like any other urethane topcoat. Care should be taken when lightly cutting metallic colors to prevent disturbing aluminum flake.


Click here to view product information sheet


Always wear proper eye, skin and respiratory protection. Always paint in a well-ventilated area away from sparks and open flame. Consult MSDS and product data sheets for proper safety precautions.


(Q) Do I need a clear?
(A) No, but you should use a clearcoat over metallics.

(Q) How much paint do I need?
(A) Typically one gallon per car. If you are also painting jambs, under the hood, or the trunk, use 2 gallons. For large cars and pickup trucks, use 2 gallons. Number of coats, prep and application methods will affect the amount of paint required.


PRE Painting Prep
Concours HVLP Paint Guns
Air Filters and Dryers
6" Liquid Ice Buffing Kit
Epoxy Primers
Urethane Primers
Polyester Primers
Clear Coats

Safety Data Sheet

Click here to view product Safety Data Sheet

Product Video

Eastwood Offers Free Lifetime Technical Support

Click here for product SDS information

Attention California Residents - Proposition 65

Proposition 65 Warning WARNING - Cancer and Reproductive Harm -

< Back

Customer Reviews

< Back

Questions & Answers

Customers also viewed: