Item # 16174ZP BRAND: Eastwood

Eastwood 4:1 Canyon Dusk Copper - Basecoat - 128oz

A beautiful copper with warm earthy tones and a striking metallic effect
A beautiful copper with warm earthy tones and a striking metallic effect
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getAggregateRating, 76.98ms
  • bvseo-msg: HTTP status code of 404 was returned;

Customize this product:

* Required Fields


Select a customization to add to cart
Save for Later
A beautiful copper with warm earthy tones and a striking metallic effect
  • 90-Day Returns
  • Technical Support
Eastwood 4:1 Canyon Dusk Copper - Basecoat - 128oz

Product Overview:


Eastwood Canyon Dusk Copper Basecoat Paint adds the superior durability of urethane to the ease of conventional basecoats.

  • Apply a durable urethane finish wherever you live in the continental US, even CA
  • Choose a fast, medium or slow Low-VOC Activator
  • Makes 5 sprayable quarts
  • Clearcoat is required on basecoat paints
  • Mixes 4:1 with your activator choice
  • Approximate coverage: 160 SQ FT
  • Flake/Pearl Particle size: 10-60 microns
  • Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
  • Made in the USA
  • A beautiful copper with warm earthy tones and a striking metallic effect

Basecoat Paint Kit is a low-VOC system, so it meets regulatory limits in highly-regulated areas, eliminating the need to switch to a waterborne system.


Made in USA


Thoroughly mix four parts Low-VOC Urethane Basecoat with one part Low-VOC Urethane Activator. Use Fast (50308ZP) for small jobs, or temps below 75°F; Medium (50309ZP) for small jobs, or temps between 70-85°F; or Slow (50310ZP) for large jobs, or temps above 80°F. Keep in mind, other factors, such as humidity, air flow and total film thickness should also be considered. In many situations, it will be useful to add 10%-20% 50104ZP Zero-VOC Reducer to aid sprayabliity, flow and leveling. Remember, this is an activated basecoat system; only mix as much as is needed. Pot life is about 2 hours at 70°F.

HVLP Gun: Fluid Tip 1.2-1.4 mm Inlet Spray Pressure 8-10 psi
Conventional Gravity: Fluid Tip 1.2-1.5 mm Inlet Spray Pressure 40-50 psi
Conventional Siphon: Fluid Tip: 1.3-1.6 mm Inlet Spray Pressure 40-50 psi

Apply Low-VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coats. Flash time should increase if additional coats are applied. Most colors will cover in two coats. A third and final coat may be applied to set even metallic pattern. If required, apply this light coat immediately after the previous full wet coat, moving the gun with faster passes, from further away. Mist basecoat onto the wet film until the metallic pattern is uniform.

Basecoat should dry dust-free within 10-20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45-90 minutes before taping on the fresh film. All dry times are approximate, at 70°. Temperature, air flow, total film thickness and other variable may extend these times.

In the Box


Urethane Basecoat, 1 gallon
Low-VOC Urethane Activator, 1 qt. (your choice of Fast, Medium or Slow)

Guides & Accessories


Click here for product instructions

Safety Information

Always wear appropriate eye, skin and respiratory protection. Consult MSDS for specific precautions and warnings .VOC = 3.5 lbs./gallon.


50104ZP Zero-VOC Urethane Paint Reducer
PRE Painting Surface Prep
Low-VOC Gray Urethane Primer
12569 Concours Master Gun Cleaning Kit
12846Z Aerosol-Injected Cleaner
SAS Bandit Respirator
Gen-Nex Painters Coveralls
15639 Concours LT HVLP Paint Gun 1.3mm

Application Tips

Choose From A Fast, Medium Or Slow Low-Voc Activator


  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 22.17ms
  • bvseo-msg: HTTP status code of 404 was returned; HTTP status code of 404 was returned;

Questions & Answers

I want to two tone the car. can i color sand metallic before clear will it change the look of the metallic base coat

Asked by: GForce
You cannot color sand Metallic paints. These need to be applied in a wet on wet process where no sanding is done.
Answered by: Scott C
Date published: 2020-09-07

I can't feel from the pics, is this a metallic paint or solar color? 

Asked by: 2smoker
This is a metallic paint.
Answered by: SeanW
Date published: 2017-10-28

Can I get a plastic model (as pictured) to judge the color in the sun and shade?  If so what is the cost? Thanks

Asked by: Hot Rod Jon
We do not have the ability to send out small plastic models of our paints. We do have a chip chart though in which this color is in.
Answered by: S Church
Date published: 2020-09-07

Will there be a color difference if I use black or grey primer?

Asked by: Ryan N
The color of your primer with this base color will not effect the overall color.
Answered by: S Church
Date published: 2019-06-13

Would it be ok to use Grey Epoxy primer w/ this color? Or should I have purchased Black?

Asked by: Rick W
The gray primer will be perfect under this paint.
Answered by: S Church
Date published: 2017-08-14
  • y_2022, m_1, d_25, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.20
  • cp_2, bvpage2n
  • co_hasquestionsanswers, tq_13
  • loc_en_US, sid_16174ZP, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 109.29ms
We found other products you might like!
Eastwood 4:1 Canyon Dusk Copper - Basecoat - 128oz
In Stock