Eastwood CONTOUR® Polyester Primer Direct to Metal Surfacer

Item #13522 Primer Surfacer

Eastwood CONTOUR® Polyester Primer Direct to Metal Surfacer
Sprayable high-build filler is an excellent base for any paint system

Eastwood CONTOUR® Polyester Primer Surfacer Qt

Item #13522ZP

- +
Quantity: close

In stock

Eastwood CONTOUR® Polyester Primer Surfacer Gal

Item #13523ZP

- +
Quantity: close

In stock

Total $0


Contour® Sprayable High-Build Primer/Surfacer serves as an excellent base for any paint system

  • High-Build With Excellent Filling Capabilities
  • Easy To Sand With No Shrinkage
  • Excellent Adhesion To Metals, Fiberglass, and Body Fillers
  • Includes hardener
  • Application: 8 mils wet = 4-6 mils dry. 10 mils wet = 6-8 mils dry.

2-component polyester primer/surfacer has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE finishes, self-etching primers and body fillers.


Contour® Sprayable Polyester Primer-Surfacer/Gray, Qt.
(1) 1 oz tube of Liquid Hardener

Contour® Sprayable Polyester Primer-Surfacer/Gray, Gal.
(2) 2 oz tubes of Liquid Hardener



1. Surface must be clean and free of wax, grease and debris. Use Eastwood’s PRE Painting Prep to remove all contaminants.

2. Sand/abrade surface
  A. Body Filler & Putty: Rough sand with 80 grit, then 180-220 and featheredge with 320 grit
  B. Untreated Steel, Galvanized and Aluminum: Sand with 80-180 grit
  C. Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish with 320 grit.

3. Completely final sand surface with 320-400 grit paper and re-clean with PRE Painting Prep

MIX: 2% by weight; 2.56 oz per Gallon; .64 oz per Quart


1.8mm to 2.5mm Fluid Tip Size, 35 to 40 PSI

Apply two or three medium wet coats as needed. Heavy wet coats should NOT be applied.
Dry spray may be removed be for recoating. Allow 90 minutes dry time before sanding at 68°F (20°C). Finish with 220 grit followed by 320-400 grit

DRY TIMES AT 68°F (20°C)

Flash: 5-10 minutes
To Sand: 90 minutes, over self etching primer: 4-6 hours
To Topcoat: 90 minutes, over self-etching primer: 4-6 hours
Force Dry: Purge 10 minutes, Bake: 30 minutes at 140°F (60°C)
Pot Life: 30 minutes at 68°F (20°C). If needed add 5-10% acetone to extend pot life.
Clean equipment with lacquer thinner immediately after use. This product is not meant for use below 60°F (16°C), dry time and performance will be dramatically affected.

CAUTION: DO NOT return catalyzed material back into can. To avoid contamination, seal lid tightly after each use. Store in a cool dry place.


Always wear eye, skin and respiratory protection when using this product. Always apply in a well-ventilated area. Consult MSDS and product label for specific safety warnings.

Eastwood Offers Free Lifetime Technical Support

Click here for product SDS information

Attention California Residents - Proposition 65

Proposition 65 Warning WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov


Customer Reviews

Questions & Answers