Item #
10331ZA
BRAND: Eastwood
Eastwood Golden CAD Aerosol 12 ounce
Replacement Gold Cad Paint for Kit 16160Z
Replacement Gold Cad Paint for Kit 16160Z
Eastwood Golden CAD Aerosol 12 ounce is rated
out of
5 by
47.
Replacement Gold Cad Paint for Kit 16160Z
Loading...
- 90-Day Returns
- Technical Support
- In Stock
Frequently Bought Together
Total Price
Description
Need just a little more Golden CAD to get you project done, we have you covered.
Golden CAD is an economical method of replicating the appearance of Golden CAD Plated parts. You can easily restore components with this easy to use system. (16160Z) This is a single replacement can of Golden CAD step #1 and is to be used if you run out of the Golden CAD that comes with the 16160Z Golden Cad Kit. One can covers approximately 6 SQ FT.
Contents
(1) 10331ZA Gold Base 12-oz. aerosol
Accessories
Eastwood Golden CAD Spray Replacement Aerosol 12oz
Application Tips
Economical Method Of Replicating The Appearance Of Golden Cad Plated Parts
Safety Information
Please wear proper personal safety equipment when using this product
Customer Reviews
Rated 5 out of
5
by
Desert_John from
Easy to use and looks great
Great product and the final product looks just like gold CAD
Date published: 2021-07-01
Rated 5 out of
5
by
ItalRestorations from
Golden Cad Kit Is Amazing! Blown Away
I recently had to restore some upper shock mounts on a car we are restoring and our plater said since there is rubber and adhesive in the mounts we can not plate them over. Tried to no avail for finding NOS and no luck so I ordered the Golden Cad Kit. Heres the info I really want to share with whomever reads this. You must properly prep the previously plated surfaces well. I soaked my parts in mineral spirits for an hour then I went over them with a gray and white 3M Scotch Brite pads as this not only cleans the corrosion but also shines the surface up enough. I then hit highlights of the parts with a fine stainless steel detail brush to further brighten areas which helps with created the right look. The Gold Cad base is a high solids but the pigment and tint is absolutely spot on compared to parts we just got back from Cad Plating. What you need to do is hit the part with light over lapping mists about 6-8 inches apart. Use a heat gun to warm the part and speed drying. You also want to leave some areas of the base thin so the shiny metal underneath will poke through which helps give this a very accurate look when done. Take the red and use a fast short burst sweep around the part, best technique is to hold the part in your hand and rotate it using a wire, just hit it on all sides then pull back about 12-14 inches and mist areas as a fill in. Let dry and then grab the green can and only hit areas you want to highlight I found tilting the can 70 degrees and short bursts gave the absolute best results. When completed you will be shocked if you master your technique how well this looks. I plan to upload photos to this review so you guys can see it because my results look superior to what others are getting and even in the Eastwood video. this was well worth the money and use.
Date published: 2020-12-26
Rated 5 out of
5
by
Dennis from
Last a good long time.
I got this to do my headlight acculators on my 68 corvette back in early 2002ish & it still has the gold on the bottom of the units, to last 15 yrs. + says a lot & it did look very good , I hope they haven't changed anything, & I would suggest the clear also for added durability.
Date published: 2019-08-26
Questions & Answers
can it be used on a carburators
The Eastwood Golden Cad Aerosol Paint(16160Z) is an excellent product for replicating the Golden Cad appearance on parts but unfortunately it is not rated as impervious to fuels and additives for carburetor painting.
Date published: 2021-01-15
Is the golden cad base coat suitable for covering metal fuel injection lines that run from the fuel injection pump to the engine block? Lines have already been primed with red oxide.
The Golden cadmium kit is not impervious to brake fluids so it would not be recommended for this application.
Date published: 2020-08-14
Following up on a previous question from 'Charles' on gas, oil and heat, it appears that this paint would not be a good candidate for valve covers on a flat-4 air-cooled engine?
This coating is only temp rated up to about 250-300F max. It is a lacquer based coating and will not offer much gas or fluid resistance.
Date published: 2019-12-11
Is this paint gas/oil resistant? Will it hold up to heat, if so to what temperature?
This paint has a temperature rating of 300°. And is not designed to be gas/oil resistant
Date published: 2019-10-29
Can automotive urethane clear be sprayed over the three-part CAD system without it wrinkling or lifting?
We do not recommend using a urethane clear over the top of this product.
Date published: 2019-09-19
New brake rotors can this product be used to paint brake rotors and will it with stand the heat of brake pressure just looking to hold on to the outer rim of brake rotor to keep it from rusting on the brake rotors so I don’t see rust.
This paint has a temperature rating of 300°. The average temperature of a rotor ranges between
125° an 300°. So we would not recommend this product for your rotors.,Any high heat product will work, as long as its rated from like 400° on up.
Date published: 2019-07-15
can this product be used on an aluminum wheel ?
This can certainly used on an aluminum wheel.
Date published: 2018-12-19
How long does each step take to "fully cure" before the next step can be started?
When each step becomes tack free you can go on to the next coat.
Date published: 2018-12-12
We found other products you might like!
Eastwood Golden CAD Aerosol 12 ounce
$19.99
In Stock